Specification sheet Wheel Loader Ref zettelmeyer-zl5002-wheel-loader
Zettelmeyer ZL5002
The Zettelmeyer ZL5002 is a wheel loader with an operating weight of 51,367.71 lb (23,300 kg), a 276.3 hp engine, and a 5.5 yd³ (4.2 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
51,367.71lb
23,300kg
Engine power
276.3hp
206kW
Net Power Bucket capacity
5.5yd³
4.2m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Zettelmeyer ZL5002 sits below the median for its class:
- Operating weight 51,370 lb lighter than 63% (n=198)
- Engine power 276 hp more powerful than 52% (n=190)
- Bucket capacity 5.5 yd³ smaller-bucket than 56% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | LTA 10-C 290 | |
| Net Power | 276.3hp | 206kw |
| Gross Power | 289.7hp | 216kw |
| Power Measured @ | 2100rpm | |
| Max Torque | 870.4lb ft | 1180Nm |
| Displacement | 622.5cu in | 10.2L |
| Torque Measured @ | 1300rpm | |
| Aspiration | turbocharged + aftercooled |
02 Operational Specification
| Operating Weight | 51367.8lb | 23300kg |
|---|---|---|
| Fuel Capacity | 95.2gal | 360L |
| Hydraulic System Fluid Capacity | 60.8gal | 230L |
| Engine Oil Fluid Capacity | 7.1gal | 26.5L |
| Transmission Fluid Capacity | 5.6gal | 21L |
| Front Axle/Diff Fluid Capacity | 14.3gal | 54L |
| Rear Axle/Diff Fluid Capacity | 13.5gal | 51L |
| Static Tipping Weight | 39132.1lb | 17750kg |
| Turning Radius | 23.9ft in | 7260mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 65amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 26.5R25 |
03 Transmission Specification
| Transmission Type | full powershift countershaft | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 23.7mph | 38km/h |
| Max Speed - Reverse | 15.6mph | 25km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3626psi | 25000kPa |
|---|---|---|
| Pump Flow Capacity | 78.8gal/min | 298L/min |
| Raise Time | 6.5sec | |
| Dump Time | 1.7sec | |
| Lower Time | 4.6sec | |
| Pump Type | tandem axial piston |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 10.6ft in | 3230mm |
|---|---|---|
| Breakout Force | 54403.76lb | 242kN |
| Bucket Capacity - Heaped | 5.5yd3 | 4.2m3 |
| Bucket Capacity - Struck | 4.71yd3 | 3.6m3 |
| Bucket Width | 9.85ft in | 3000mm |
06 Dimensions Dimensions
| Ground Clearance | 1.61ft in | 490mm |
|---|---|---|
| Length With Bucket On Ground | 28.97ft in | 8830mm |
| Height To Top Of Cab | 11.46ft in | 3490mm |
| Wheelbase | 12.14ft in | 3700mm |
| Hinge Pin - Max Height | 14.6ft in | 4450mm |
| Reach At Max Lift And Dump | 3.75ft in | 1140mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.