Specification sheet Wheel Loader Ref zettelmeyer-zl4002-wheel-loader
Zettelmeyer ZL4002
The Zettelmeyer ZL4002 is a wheel loader with an operating weight of 46,958.47 lb (21,300 kg), a 240 hp engine, and a 4.58 yd³ (3.5 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
46,958.47lb
21,300kg
Engine power
240hp
179kW
Net Power Bucket capacity
4.58yd³
3.5m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Zettelmeyer ZL4002 sits at the compact end of its class:
- Operating weight 46,960 lb lighter than 88% (n=198)
- Engine power 240 hp less powerful than 85% (n=190)
- Bucket capacity 4.6 yd³ smaller-bucket than 90% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | LT 10-C 250 | |
| Net Power | 240hp | 179kw |
| Gross Power | 250hp | 186.5kw |
| Power Measured @ | 2100rpm | |
| Max Torque | 743.5lb ft | 1008Nm |
| Displacement | 622.5cu in | 10.2L |
| Torque Measured @ | 1300rpm | |
| Aspiration | turbocharged |
02 Operational Specification
| Operating Weight | 46958.5lb | 21300kg |
|---|---|---|
| Fuel Capacity | 95.2gal | 360L |
| Hydraulic System Fluid Capacity | 60.8gal | 230L |
| Engine Oil Fluid Capacity | 7.1gal | 26.5L |
| Transmission Fluid Capacity | 7.4gal | 28L |
| Front Axle/Diff Fluid Capacity | 11.1gal | 42L |
| Rear Axle/Diff Fluid Capacity | 8.2gal | 31L |
| Static Tipping Weight | 37919.6lb | 17200kg |
| Turning Radius | 22.7ft in | 6910mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 65amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 26.5-25 16PR |
03 Transmission Specification
| Transmission Type | full powershift countershaft | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 23.7mph | 38km/h |
| Max Speed - Reverse | 14.3mph | 23km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3335.9psi | 23000kPa |
|---|---|---|
| Pump Flow Capacity | 78.8gal/min | 298L/min |
| Raise Time | 6.5sec | |
| Dump Time | 1.7sec | |
| Lower Time | 4.6sec | |
| Pump Type | tandem axial piston pump |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 10.73ft in | 3270mm |
|---|---|---|
| Breakout Force | 50582.01lb | 225kN |
| Bucket Capacity - Heaped | 4.58yd3 | 3.5m3 |
| Bucket Capacity - Struck | 3.93yd3 | 3m3 |
| Bucket Width | 9.85ft in | 3000mm |
06 Dimensions Dimensions
| Ground Clearance | 1.61ft in | 490mm |
|---|---|---|
| Length With Bucket On Ground | 27.43ft in | 8360mm |
| Height To Top Of Cab | 11.49ft in | 3500mm |
| Wheelbase | 11.65ft in | 3550mm |
| Hinge Pin - Max Height | 14.44ft in | 4400mm |
| Reach At Max Lift And Dump | 3.48ft in | 1060mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.