Specification sheet Skid Steer Loader Ref yanmar-s220r-1-skid-steer-loader

Yanmar S220R-1

The Yanmar S220R-1 is a skid steer loader with an operating weight of 7,980.74 lb (3,620 kg), a 70.68 hp engine, a rated operating capacity of 2,200.3 lb (998 kg), and a tipping load of 4,398.3 lb (1,995.04 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
7,980.74lb
3,620kg
Engine power
70.68hp
52.7kW
Net Power
Rated operating capacity
2,200.3lb
998kg
Tipping load
4,398.3lb † — value reconstructed from related published figures
1,995.04kg

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Yanmar S220R-1 sits above the median for its class:

  • Operating weight 7,980 lb heavier than 78% (n=334)
  • Engine power 71 hp more powerful than 61% (n=335)
  • Rated operating capacity 2,200 lb higher-rated than 69% (n=288)

◇Scale drawingdrawn to scale · mm

4089C203D3467A2667B
Side elevation
4089C1664E
Front elevation

01 Engine Specification

Engine Make Yanmar
Engine Model 4TNV98CT-NMS
Net Power 70.7hp 52.7kw
Power Measured @ 2500rpm
Displacement 202.6cu in 3.4L

02 Capacities Specification

Rated Operating Capacity 2200.3lb 998kg

03 Operational Specification

Operational Weight 7980.8lb 3620kg
Fuel Capacity 18gal 68.1L
Max Speed 11.4mph 18.3km/h
Tire Size 12.00 x 16.5 HD

04 Electrical Specification

Alternator 95amps
Starter Size 12-volt (3.0 kW)
Battery 12-volt (950 CCA)

05 Weights Specification

With Optional Counterweight 2370lb 1075kg

06 Loader Specification

Bucket Width 70in 1778mm

07 Hydraulic Specification

Hydraulic Reservoir 12gal 45.5L
Auxiliary Hydraulic Flow 23.6gal/min 89L/min
Relief Valve Pressure 3300psi 22752.7kPa

08 Dimensions Dimensions

Length With Bucket 11.38ft in 3467mm
Ground Clearance 8in 203mm
Height To Top Of Cab 13.42ft in 4089mm
Wheelbase 3.59ft in 1092mm
Length W/O Bucket 8.75ft in 2667mm
Reach At Max Lift And Dump 27.01in 686mm
Hinge Pin Height - Fully Raised 123in 3124mm
Dump Angle 40degrees
Front Departure Angle 25degrees
Overall Height, Rops Cab 80.99in 2057mm
Overall Width 5.46ft in 1664mm
Rollback - Ground Level 28degrees
Ground Height 40in 1016mm
Dump Height 7.84ft in 2388mm

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.