Specification sheet Wheel Loader Ref terex-txl250-1-wheel-loader
Terex TXL250-1
The Terex TXL250-1 is a wheel loader with an operating weight of 30,420 lb (13,798.28 kg), a 163 hp engine, and a 3.14 yd³ (2.4 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
30,420lb
13,798.28kg
Engine power
163hp
121.55kW
Gross Power Bucket capacity
3.14yd³
2.4m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Terex TXL250-1 sits in the middle of its class:
- Operating weight 30,420 lb lighter than 52% (n=439)
- Engine power 163 hp less powerful than 51% (n=408)
- Bucket capacity 3.1 yd³ smaller-bucket than 53% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2253 | |
| Engine Model | DB58Tis | |
| Gross Power | 163hp | 121.6kw |
| Power Measured @ | 2200rpm | |
| Max Torque | 524lb ft | 710.5Nm |
| Displacement | 353cu in | 5.8L |
| Torque Measured @ | 1300rpm | |
| Aspiration | turbocharged |
02 Operational Specification
| Operating Weight | 30420lb | 13798.3kg |
|---|---|---|
| Fuel Capacity | 71.4gal | 270L |
| Hydraulic System Fluid Capacity | 51.6gal | 195L |
| Engine Oil Fluid Capacity | 5.6gal | 21L |
| Cooling System Fluid Capacity | 13.3gal | 50L |
| Transmission Fluid Capacity | 9.3gal | 35L |
| Front Axle/Diff Fluid Capacity | 7.3gal | 27.5L |
| Rear Axle/Diff Fluid Capacity | 7.3gal | 27.5L |
| Static Tipping Weight | 26455.5lb | 12000kg |
| Turning Radius | 19.9ft in | 6051mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 65amps | |
| Rear Axle Oscillation | 22degrees | |
| Tire Size | 20.5x25x16PR |
03 Transmission Specification
| Transmission Type | full auto powershift countershaft | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 23mph | 37km/h |
| Max Speed - Reverse | 14.7mph | 23.5km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 2845psi | 19615.6kPa |
|---|---|---|
| Pump Flow Capacity | 66gal/min | 249.9L/min |
| Raise Time | 5.3sec | |
| Dump Time | 1.2sec | |
| Lower Time | 3.3sec | |
| Pump Type | vane type |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.06ft in | 2760mm |
|---|---|---|
| Bucket Capacity - Heaped | 3.14yd3 | 2.4m3 |
| Bucket Width | 8.99ft in | 2740mm |
| Breakout Force | 29100lb | 129.37kN |
06 Dimensions Dimensions
| Ground Clearance | 1.42ft in | 430mm |
|---|---|---|
| Length With Bucket On Ground | 24.61ft in | 7500mm |
| Height To Top Of Cab | 10.9ft in | 3320mm |
| Wheelbase | 9.91ft in | 3020mm |
| Hinge Pin - Max Height | 12.77ft in | 3890mm |
| Reach At Max Lift And Dump | 3.75ft in | 1143mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.