Terex HR1.6
The Terex HR1.6 is a mini excavator with an operating weight of 3,659.7 lb, a 18 hp engine, and a dig depth of 7.22 ft.
✓ QA-verified — every figure checked for physical possibility and class plausibility; failures withheld →◆Where it sits in its classpercentile · mini excavators
Among 479 mini excavators , the Terex HR1.6 sits below the median for its class:
- Operating weight 3,660 lb lighter than 83% (n=438)
- Engine power 18 hp less powerful than 74% (n=448)
- Dig depth 7.2 ft shallower-digging than 84% (n=426)
01 Boom/Stick Option (Hex) 1 Specification
| Max Cutting Height | 11.16ft in | 3,402mm‖ — metric converted from the published imperial value |
|---|---|---|
| Max Loading Height | 7.55ft in | 2,301mm‖ — metric converted from the published imperial value |
| Max Reach Along Ground | 12.8ft in | 3,901mm‖ — metric converted from the published imperial value |
| Max Vertical Wall Digging Depth | 3.61ft in | 1,100mm‖ — metric converted from the published imperial value |
| Max Digging Depth | 7.22ft in | 2,201mm‖ — metric converted from the published imperial value |
| Boom/Stick Option (Hex) 1 | Monobloc boom Dipperstick 1100mm |
02 Boom/Stick Option (Hex) 2 Specification
| Max Cutting Height | 11.49ft in | 3,502mm‖ — metric converted from the published imperial value |
|---|---|---|
| Max Loading Height | 7.88ft in | 2,402mm‖ — metric converted from the published imperial value |
| Max Reach Along Ground | 13.46ft in | 4,103mm‖ — metric converted from the published imperial value |
| Max Vertical Wall Digging Depth | 3.94ft in | 1,201mm‖ — metric converted from the published imperial value |
| Max Digging Depth | 7.88ft in | 2,402mm‖ — metric converted from the published imperial value |
| Boom/Stick Option (Hex) 2 | Monobloc boom Dipperstick 1300mm |
03 Dimensions Specification
| Width To Outside Of Tracks | 3.61ft in | 1,100mm‖ — metric converted from the published imperial value |
|---|---|---|
| Ground Clearance | 0.56ft in | 171mm‖ — metric converted from the published imperial value |
| Tail Swing Radius | 3.61ft in | 1,100mm‖ — metric converted from the published imperial value |
04 Undercarriage Specification
| Max Travel Speed | 1.87mph | 3.01km/h‖ — metric converted from the published imperial value |
|---|---|---|
| Drawbar Pull | 2610lb | 1,184kg‖ — metric converted from the published imperial value |
05 Engine Specification
| Engine Make | 2251 | |
|---|---|---|
| Engine Model | L3E-W 262 KL | |
| Gross Power | 18hp | 13kw‖ — metric converted from the published imperial value |
| Power Measured @ | 2400rpm | |
| Displacement | 58cu in | 950cm3‖ — metric converted from the published imperial value |
| Max Torque | 39.9lb ft | |
| Torque Measured @ | 1500rpm |
06 Operational Specification
| Operating Weight | 3659.7lb | 1,660kg‖ — metric converted from the published imperial value |
|---|---|---|
| Fuel Capacity | 8.2gal | 31l‖ — metric converted from the published imperial value |
| Hydraulic System Fluid Capacity | 9.8gal | 37l‖ — metric converted from the published imperial value |
| Operational Voltage | 12V | |
| Hydraulic System Relief Valve Pressure | 2395psi | 16,513kpa‖ — metric converted from the published imperial value |
| Hydraulic Pump Flow Capacity | 14gal/min | 53l/min‖ — metric converted from the published imperial value |
07 Swing Mechanism Specification
| Swing Speed | 10rpm |
|---|
Data notes
Converted metric figure. The source published imperial figures only for this machine. Metric figures marked ‖ are unit conversions of the published imperial value, rounded to the same precision — they are not separately published measurements. Because there is no independently published metric figure to compare against, no cross-unit consistency check applies to them; the imperial figures they derive from were checked for physically possible magnitude and for plausibility against this equipment class.
Method. Figures are manufacturer reference specifications, not measurements. The source published imperial figures for this machine in a single unit system, so no cross-unit consistency check applies; every value is checked for physically possible magnitude and for plausibility against its equipment class before publication. Figures that fail either check are withheld rather than shown, and figures reconstructed from related data are marked above. Metric figures marked ‖ are converted from the published imperial value rather than reproduced from the source.