Mustang MTL20
The Mustang MTL20 is a compact track loader with an operating weight of 9,590.11 lb (4,350 kg), a 80.5 hp engine, a rated operating capacity of 2,976.25 lb (1,350 kg), and a tipping load of 5,952.5 lb (2,700.01 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · compact track loaders
Among 184 compact track loaders , the Mustang MTL20 sits in the middle of its class:
- Operating weight 9,590 lb heavier than 55% (n=182)
- Engine power 81 hp more powerful than 65% (n=167)
- Rated operating capacity 2,980 lb higher-rated than 62% (n=156)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2353 | |
| Engine Model | 4JG1T | |
| Gross Power | 80.5hp | 60kw |
| Power Measured @ | 2400rpm | |
| Peak Torque | 190.3lb ft | 258Nm |
| Torque Measured @ | 1800rpm | |
| Displacement | 189.2cu in | 3.1L |
| Aspiration | turbocharged |
02 Operational Specification
| Operating Weight | 9590.2lb | 4350kg |
|---|---|---|
| Cooling System Fluid Capacity | 4gal | 15.1L |
| Fuel Capacity | 23.8gal | 90L |
| Engine Oil Capacity | 2.5gal | 9.4L |
| Hydraulic System Fluid Capacity | 22gal | 83L |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 50amps | |
| Max Speed - Low Range | 4.5mph | 7.2km/h |
| Max Speed - High Range | 6.5mph | 10.3km/h |
03 Loader Specification
| Breakout Force | 7401lb | 3357.1kg |
|---|---|---|
| Operating Load | 2976.3lb | 1350kg |
| Bucket Capacity | 0.8yd3 | 0.6m3 |
04 Hydraulic Specification
| Pump Flow | 19.9gal/min | 75L/min |
|---|---|---|
| Relief Valve Pressure | 2987.8psi | 20600kPa |
05 Dimensions Dimensions
| Width Over Tracks | 5.81ft in | 1770mm |
|---|---|---|
| Height To Top Of Cab | 7.11ft in | 2167mm |
| Ground Clearance | 12.8in | 325mm |
| Clearance At Max Lift And Dump | 7.91ft in | 2408mm |
| Reach At Max Lift And Dump | 2.87ft in | 874mm |
| Turning Radius From Center - Machine Rear | 65.6in | 1666mm |
| Length With Bucket | 12.17ft in | 3708mm |
| Turning Radius From Center - Inc Bucket | 90.32in | 2294mm |
| Length With Out Bucket | 9.68ft in | 2949mm |
06 Undercarriage Dimensions
| Length Of Track On Ground | 4.92ft in | 1499mm |
|---|---|---|
| Track Gauge | 4.31ft in | 1313mm |
| Ground Contact Area | 1060in2 | 0.69m2 |
| Number Of Track Rollers Per Side | 4 | |
| Width Of Track | 18in | 457mm |
| Ground Pressure | 4.1psi | 28.27kPa |
?Questions & answersfrom this machine's data
- How much does a Mustang MTL20 compact track loader weigh?
- A Mustang MTL20 compact track loader has an operating weight of 9,590.1 lb (4,350 kg).
- How much can a Mustang MTL20 compact track loader lift?
- A Mustang MTL20 compact track loader has a rated operating capacity of 2,976.3 lb (1,350 kg).
- What engine does a Mustang MTL20 compact track loader have?
- A Mustang MTL20 compact track loader is powered by a 4JG1T engine producing 80.5 hp (60 kW).
- How much fuel does a Mustang MTL20 compact track loader hold?
- A Mustang MTL20 compact track loader has a fuel capacity of 23.8 gal (90 L).
- What is the ground clearance of a Mustang MTL20 compact track loader?
- A Mustang MTL20 compact track loader has a ground clearance of 12.8 in (325 mm).
- How long is a Mustang MTL20 compact track loader?
- A Mustang MTL20 compact track loader has an overall length of 12.2 ft (3,708 mm) with the bucket on the ground.
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.