Specification sheet Wheel Loader Ref michigan-l140-wheel-loader
Michigan L140
The Michigan L140 is a wheel loader with an operating weight of 42,220 lb (19,150.67 kg), a 203 hp engine, and a 4.01 yd³ (3.06 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
42,220lb
19,150.67kg
Engine power
203hp
151.4kW
Net Power Bucket capacity
4.01yd³
3.06m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Michigan L140 sits at the heavy end of its class:
- Operating weight 42,220 lb heavier than 92% (n=439)
- Engine power 203 hp more powerful than 80% (n=408)
- Bucket capacity 4 yd³ larger-bucket than 79% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | LT-10-225 HT | |
| Net Power | 203hp | 151.4kw |
| Gross Power | 225hp | 167.8kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 750lb ft | 1016.9Nm |
| Displacement | 611cu in | 10.1L |
| Torque Measured @ | 1300rpm | |
| Aspiration | turbocharged & aftercooled |
02 Operational Specification
| Operating Weight | 42220lb | 19150.7kg |
|---|---|---|
| Fuel Capacity | 90.9gal | 344L |
| Hydraulic System Fluid Capacity | 87gal | 329L |
| Engine Oil Fluid Capacity | 9.1gal | 34.1L |
| Cooling System Fluid Capacity | 15.1gal | 56.8L |
| Transmission Fluid Capacity | 10.6gal | 39.8L |
| Front Axle/Diff Fluid Capacity | 8.6gal | 32.2L |
| Rear Axle/Diff Fluid Capacity | 8.6gal | 32.2L |
| Static Tipping Weight | 33060.6lb | 14996kg |
| Turning Radius | 24.5ft in | 7442mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 100amps | |
| Rear Axle Oscillation | 18.5degrees | |
| Tire Size | 23.5-25 (16PR) L-3 |
03 Transmission Specification
| Transmission Type | Clark R32425-6 | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 19.9mph | 32.1km/h |
| Max Speed - Reverse | 19.9mph | 32.1km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 2750psi | 18960.6kPa |
|---|---|---|
| Pump Flow Capacity | 31gal/min | 117.4L/min |
| Raise Time | 7.5sec | |
| Dump Time | 1.5sec | |
| Lower Time | 2sec | |
| Pump Type | gear type |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.8ft in | 2985mm |
|---|---|---|
| Bucket Capacity - Heaped | 4.01yd3 | 3.06m3 |
| Bucket Capacity - Struck | 3.41yd3 | 2.6m3 |
| Bucket Width | 10.34ft in | 3150mm |
| Breakout Force | 43100lb | 191.7kN |
06 Dimensions Dimensions
| Ground Clearance | 1.42ft in | 432mm |
|---|---|---|
| Length With Bucket On Ground | 27.17ft in | 8280mm |
| Width Over Tires | 9.42ft in | 2870mm |
| Height To Top Of Cab | 11.59ft in | 3531mm |
| Wheelbase | 10.67ft in | 3251mm |
| Hinge Pin - Max Height | 13.26ft in | 4039mm |
| Reach At Max Lift And Dump | 3.42ft in | 1041mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.