Mecalac 10MCR
The Mecalac 10MCR is a mini excavator with an operating weight of 27,778.3 lb, a 75 hp engine, and a dig depth of 13.13 ft.
✓ QA-verified — every figure checked for physical possibility and class plausibility; failures withheld →◆Where it sits in its classpercentile · mini excavators
Among 479 mini excavators , the Mecalac 10MCR sits at the heavy end of its class:
- Operating weight 27,780 lb heavier than 99% (n=438)
- Engine power 75 hp more powerful than 99% (n=448)
- Dig depth 13.1 ft deeper-digging than 96% (n=426)
01 Boom/Stick Option (Hex) 1 Specification
| Max Vertical Wall Digging Depth | 7.55ft in | 2,301mm‖ — metric converted from the published imperial value |
|---|---|---|
| Max Digging Depth | 13.13ft in | 4,002mm‖ — metric converted from the published imperial value |
| Maximum Reach At Ground Level | 24.61ft in | 7,501mm‖ — metric converted from the published imperial value |
02 Dimensions Specification
| Ground Clearance | 1.12ft in | 341mm‖ — metric converted from the published imperial value |
|---|---|---|
| Turning Radius | 10.72ft in | 3,267mm‖ — metric converted from the published imperial value |
| Overall Height | 10.67ft in | 3,252mm‖ — metric converted from the published imperial value |
| Overall Length | 131.66in | 3,344.2mm‖ — metric converted from the published imperial value |
| Tumbler Length | 7.45ft in | 2,271mm‖ — metric converted from the published imperial value |
03 Undercarriage Specification
| Rubber Tracks | 17.72in | 450.1mm‖ — metric converted from the published imperial value |
|---|---|---|
| Steel Tracks | 15.75in | 400mm‖ — metric converted from the published imperial value |
| Number Of Track Rollers Per Side | 6 | |
| Tractive Effort | 6800lb | 3,084kg‖ — metric converted from the published imperial value |
| Number Of Carrier Rollers Per Side | 1 |
04 Engine Specification
| Starter | 3.7hp | 2.8kw‖ — metric converted from the published imperial value |
|---|---|---|
| Engine Model | DEUTZ TCD 3,6 L4 | |
| Gross Power | 75hp | 56kw‖ — metric converted from the published imperial value |
| Power Measured @ | 2200rpm | |
| Battery | 12 Volts (100 AH) | |
| Max Torque | 390lb ft | |
| Torque Measured @ | 1300rpm | |
| Alternator | 95amps |
05 Operational Specification
| Travel Speed, Low Range | 2mph | 3km/h‖ — metric converted from the published imperial value |
|---|---|---|
| Travel Speed, High Range | 3.5mph | 5.6km/h‖ — metric converted from the published imperial value |
| Ground Pressure Rubber Tracks | 17.8in | 452mm‖ — metric converted from the published imperial value |
| Ground Pressure Steel Tracks | 1.4ft in | 427mm‖ — metric converted from the published imperial value |
| Operating Weight | 27778.3lb | 12,600kg‖ — metric converted from the published imperial value |
| Fuel Capacity | 27.8gal | 105l‖ — metric converted from the published imperial value |
| Cooling System Fluid Capacity | 4.3gal | 16l‖ — metric converted from the published imperial value |
| Operational Voltage | 12V | |
| Hydraulic Pump Flow Capacity | 20.4gal/min | 77.2l/min‖ — metric converted from the published imperial value |
06 Transmission Specification
| Pump Flow | 52.9gal/min | 200l/min‖ — metric converted from the published imperial value |
|---|
07 Blade Specification
| Blade Lift Height | 9.8in | 249mm‖ — metric converted from the published imperial value |
|---|---|---|
| Blade Height | 1.4ft in | 427mm‖ — metric converted from the published imperial value |
| Width | 7.6ft in | 2,316mm‖ — metric converted from the published imperial value |
Data notes
Converted metric figure. The source published imperial figures only for this machine. Metric figures marked ‖ are unit conversions of the published imperial value, rounded to the same precision — they are not separately published measurements. Because there is no independently published metric figure to compare against, no cross-unit consistency check applies to them; the imperial figures they derive from were checked for physically possible magnitude and for plausibility against this equipment class.
Method. Figures are manufacturer reference specifications, not measurements. The source published imperial figures for this machine in a single unit system, so no cross-unit consistency check applies; every value is checked for physically possible magnitude and for plausibility against its equipment class before publication. Figures that fail either check are withheld rather than shown, and figures reconstructed from related data are marked above. Metric figures marked ‖ are converted from the published imperial value rather than reproduced from the source.