Specification sheet Wheel Loader Ref liebherr-l586-xpower-wheel-loader
Liebherr L586 XPOWER
The Liebherr L586 XPOWER is a wheel loader with an operating weight of 71,870 lb (32,599.69 kg), a 349 hp engine, a 7.8 yd³ (5.97 m³) bucket, and a dig depth of 4 ft (1,219.2 mm).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
71,870lb
32,599.69kg
Engine power
349hp
260.3kW
Net Power Bucket capacity
7.8yd³
5.97m³
Dig depth
4ft
1,219.2mm
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Liebherr L586 XPOWER sits at the heavy end of its class:
- Operating weight 71,870 lb heavier than 95% (n=198)
- Engine power 349 hp more powerful than 92% (n=190)
- Bucket capacity 7.8 yd³ larger-bucket than 96% (n=174)
◇Scale drawingdrawn to scale · mm
01 Electrical System Specification
| Alternator | 28/180 (V/A) | |
|---|---|---|
| Voltage | 24 VV | |
| Starter | 24/10.5 (V/HP) | |
| Battery | 2 x 180 Ah |
02 Engine Specification
| Fuel Injection | Electronic Common Rail high-pressure injection | |
|---|---|---|
| Number Of Cylinders | 6 | |
| Engine Model | D936 A7 | |
| Net Power | 349hp | 260.3kw |
| Air Cleaner | Dry type filter with main and safety element, pre-cleaner, service indicator on the Liebherr display | |
| Gross Power | 353hp | 263.3kw |
| Power Measured @ | 1800rpm | |
| Max Torque | 1450 lb ft | |
| Displacement | 642cu in | 10.6L |
| Torque Measured @ | 1100rpm | |
| Aspiration | Water-cooled in-line engine with charge-air cooling, exhaust after-treatment through Liebherr-SCR technology | |
| Bore | 4.8in | 122mm |
| Stroke | 6in | 150.2mm |
03 Operational Specification
| Operating Weight | 71870lb | 32599.7kg |
|---|---|---|
| Fuel Capacity | 132gal | 499.7L |
| Hydraulic System Fluid Capacity | 55.5gal | 210.1L |
| Engine Oil Fluid Capacity | 10.6gal | 40.2L |
| Cooling System Fluid Capacity | 19.3gal | 73.1L |
| Hydraulic Fluid Capacity | 25.1gal | 95.1L |
| Front Axle/Diff Fluid Capacity | 15.9gal | 60.2L |
| Rear Axle/Diff Fluid Capacity | 15.9gal | 60.2L |
| Static Tipping Weight | 47620lb | 21600.1kg |
| Turning Radius | 27.5ft in | 8382mm |
| Tire Size | 29.5R25 L3 |
04 Transmission Specification
| Max Speed - Forward | 20.5mph | 33km/h |
|---|---|---|
| Max Speed - Reverse | 20.5mph | 33km/h |
05 Hydraulic System Specification
| Max Operating Pressure | 4786 psi | |
|---|---|---|
| Relief Valve Setting | 4351.2psi | 30000kPa |
| Pump Flow Capacity | 108gal/min | 408.9L/min |
| Raise Time | 6.5sec | |
| Dump Time | 3sec | |
| Lower Time | 4sec | |
| Pump Type | “Load-sensing” variable axial piston pump with output and flow control, and pressure cut-off in the control block |
06 Bucket Dimensions
| Dump Clearance At Max Raise | 10.8ft in | 3291.84mm |
|---|---|---|
| Arm Length | 10.4ft in | 3169.92mm |
| Breakout Force | 53954.15lb | 240kN |
| Bucket Capacity - Heaped | 7.8yd3 | 5.97m3 |
| Bucket Width | 11.3ft in | 3444.24mm |
| Digging Depth | 4ft in | 1219.2mm |
07 Dimensions Dimensions
| Ground Clearance | 1.12ft in | 338.33mm |
|---|---|---|
| Length With Bucket On Ground | 32.9ft in | 10027.92mm |
| Height To Top Of Cab | 12.3ft in | 3749.04mm |
| Wheelbase | 12.1ft in | 3688.08mm |
| Hinge Pin - Max Height | 15.3ft in | 4663.44mm |
| Reach At Max Lift And Dump | 4.8ft in | 1463.04mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.