Specification sheet Wheel Loader Ref liebherr-l580-2plus2-wheel-loader
Liebherr L580 2plus2
The Liebherr L580 2plus2 is a wheel loader with an operating weight of 54,542.37 lb (24,740 kg), a 265 hp engine, and a 6.54 yd³ (5 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
54,542.37lb
24,740kg
Engine power
265hp
197.62kW
Gross Power Bucket capacity
6.54yd³
5m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Liebherr L580 2plus2 sits in the middle of its class:
- Operating weight 54,540 lb heavier than 53% (n=198)
- Engine power 265 hp less powerful than 65% (n=190)
- Bucket capacity 6.5 yd³ larger-bucket than 80% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2245 | |
| Engine Model | D 926 TI-E A2 | |
| Gross Power | 265hp | 197.7kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 947.8lb ft | 1285Nm |
| Torque Measured @ | 1200rpm | |
| Aspiration | turbo-charged with intercooler |
02 Operational Specification
| Operating Weight | 54542.4lb | 24740kg |
|---|---|---|
| Fuel Capacity | 87.2gal | 330L |
| Hydraulic System Fluid Capacity | 63.5gal | 240L |
| Engine Oil Fluid Capacity | 6.3gal | 23.5L |
| Front Axle/Diff Fluid Capacity | 15.4gal | 58L |
| Rear Axle/Diff Fluid Capacity | 13.3gal | 50L |
| Static Tipping Weight | 44665.7lb | 20260kg |
| Turning Radius | 23.8ft in | 7250mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 55amps | |
| Rear Axle Oscillation | 26degrees | |
| Tire Size | 26.5R25 |
03 Transmission Specification
| Transmission Type | hydrostatic 2plus2 | |
|---|---|---|
| Number Of Forward Gears | 3 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.9mph | 40km/h |
| Max Speed - Reverse | 24.9mph | 40km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 5076.4psi | 35000kPa |
|---|---|---|
| Pump Flow Capacity | 76.7gal/min | 290L/min |
| Raise Time | 5.5sec | |
| Dump Time | 2sec | |
| Lower Time | 3.5sec | |
| Pump Type | Load-sensing variable axial piston pump with output control and pressure cut-off |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 10.83ft in | 3300mm |
|---|---|---|
| Bucket Capacity - Heaped | 6.54yd3 | 5m3 |
| Bucket Width | 10.83ft in | 3300mm |
| Breakout Force | 39341.57lb | 175kN |
06 Dimensions Dimensions
| Ground Clearance | 1.81ft in | 550mm |
|---|---|---|
| Length With Bucket On Ground | 29.53ft in | 9000mm |
| Height To Top Of Cab | 11.62ft in | 3540mm |
| Wheelbase | 11.72ft in | 3570mm |
| Hinge Pin - Max Height | 14.97ft in | 4560mm |
| Reach At Max Lift And Dump | 3.78ft in | 1150mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.