Specification sheet Wheel Loader Ref liebherr-l574-2plus2-wheel-loader
Liebherr L574 2plus2
The Liebherr L574 2plus2 is a wheel loader with an operating weight of 53,462.11 lb (24,250 kg), a 265 hp engine, and a 5.89 yd³ (4.5 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
53,462.11lb
24,250kg
Engine power
265hp
197.62kW
Gross Power Bucket capacity
5.89yd³
4.5m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Liebherr L574 2plus2 sits in the middle of its class:
- Operating weight 53,460 lb heavier than 51% (n=198)
- Engine power 265 hp less powerful than 65% (n=190)
- Bucket capacity 5.9 yd³ larger-bucket than 60% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2245 | |
| Engine Model | D 926 TI-E A2 | |
| Gross Power | 265hp | 197.7kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 947.8lb ft | 1285Nm |
| Displacement | 607.8cu in | 10L |
| Torque Measured @ | 1200rpm | |
| Aspiration | Inline engine, water-cooled exhaust-turbo charged with intercooler |
02 Operational Specification
| Operating Weight | 53462.2lb | 24250kg |
|---|---|---|
| Fuel Capacity | 87.2gal | 330L |
| Hydraulic System Fluid Capacity | 63.5gal | 240L |
| Engine Oil Fluid Capacity | 6.3gal | 23.5L |
| Front Axle/Diff Fluid Capacity | 13.5gal | 51L |
| Rear Axle/Diff Fluid Capacity | 13.5gal | 51L |
| Static Tipping Weight | 40454.9lb | 18350kg |
| Turning Radius | 23.3ft in | 7090mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 55amps | |
| Rear Axle Oscillation | 26degrees | |
| Tire Size | 26.5 R 25 |
03 Transmission Specification
| Transmission Type | Stepless hydrostatic travel drive 2plus2 | |
|---|---|---|
| Number Of Forward Gears | 3 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.9mph | 40km/h |
| Max Speed - Reverse | 24.9mph | 40km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 5076.4psi | 35000kPa |
|---|---|---|
| Pump Flow Capacity | 76.7gal/min | 290L/min |
| Raise Time | 5.6sec | |
| Dump Time | 2sec | |
| Lower Time | 3.5sec | |
| Pump Type | Load-sensing, variable axial piston pump with output control and pressure cutoff |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 10.83ft in | 3300mm |
|---|---|---|
| Bucket Capacity - Heaped | 5.89yd3 | 4.5m3 |
| Bucket Width | 9.85ft in | 3000mm |
| Breakout Force | 39341.57lb | 175kN |
06 Dimensions Dimensions
| Ground Clearance | 1.81ft in | 550mm |
|---|---|---|
| Length With Bucket On Ground | 29.47ft in | 8980mm |
| Height To Top Of Cab | 11.62ft in | 3540mm |
| Wheelbase | 11.32ft in | 3450mm |
| Hinge Pin - Max Height | 14.98ft in | 4565mm |
| Reach At Max Lift And Dump | 4.17ft in | 1270mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.