Specification sheet Wheel Loader Ref liebherr-l566-2plus2-wheel-loader
Liebherr L566 2plus2
The Liebherr L566 2plus2 is a wheel loader with an operating weight of 49,604.02 lb (22,500 kg), a 254.8 hp engine, and a 5.24 yd³ (4 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
49,604.02lb
22,500kg
Engine power
254.8hp
190kW
Gross Power Bucket capacity
5.24yd³
4m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Liebherr L566 2plus2 sits below the median for its class:
- Operating weight 49,600 lb lighter than 76% (n=198)
- Engine power 255 hp less powerful than 78% (n=190)
- Bucket capacity 5.2 yd³ smaller-bucket than 72% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Engine Make | 2245 | |
|---|---|---|
| Engine Model | D 936 L A6 | |
| Gross Power | 254.8hp | 190kw |
| Max Torque | 907.3lb ft | 1230Nm |
| Displacement | 642cu in | 10.6L |
| Aspiration | turbo-charged |
02 Operational Specification
| Operating Weight | 49604.1lb | 22500kg |
|---|---|---|
| Fuel Capacity | 105.7gal | 400L |
| Hydraulic System Fluid Capacity | 68.7gal | 260L |
| Engine Oil Fluid Capacity | 11.4gal | 43L |
| Cooling System Fluid Capacity | 13.8gal | 52L |
| Front Axle/Diff Fluid Capacity | 13.5gal | 51L |
| Rear Axle/Diff Fluid Capacity | 13.5gal | 51L |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 80amps | |
| Rear Axle Oscillation | 26degrees | |
| Tire Size | 26.5R25 |
03 Transmission Specification
| Transmission Type | hydrostatic | |
|---|---|---|
| Number Of Forward Gears | 3 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.9mph | 40km/h |
| Max Speed - Reverse | 24.9mph | 40km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 5076.4psi | 35000kPa |
|---|---|---|
| Pump Flow Capacity | 76.7gal/min | 290L/min |
| Raise Time | 5.5sec | |
| Dump Time | 2sec | |
| Lower Time | 3.5sec | |
| Pump Type | Load-sensing swash plate type variable flow pump with output and flow control and pressure cut-off in the control block |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 10.63ft in | 3240mm |
|---|---|---|
| Breakout Force | _- | 200kN |
| Bucket Capacity - Heaped | 5.24yd3 | 4m3 |
| Bucket Width | 9.85ft in | 3000mm |
06 Dimensions Dimensions
| Ground Clearance | 1.86ft in | 565mm |
|---|---|---|
| Length With Bucket On Ground | 29.24ft in | 8912mm |
| Height To Top Of Cab | 11.65ft in | 3550mm |
| Wheelbase | 11.75ft in | 3580mm |
| Hinge Pin - Max Height | 14.31ft in | 4360mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.