Specification sheet Wheel Loader Ref liebherr-l554-2plus2-wheel-loader
Liebherr L554 2plus2
The Liebherr L554 2plus2 is a wheel loader with an operating weight of 38,139.98 lb (17,300 kg), a 198 hp engine, and a 4.58 yd³ (3.5 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
38,139.98lb
17,300kg
Engine power
198hp
147.65kW
Gross Power Bucket capacity
4.58yd³
3.5m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Liebherr L554 2plus2 sits above the median for its class:
- Operating weight 38,140 lb heavier than 78% (n=439)
- Engine power 198 hp more powerful than 75% (n=408)
- Bucket capacity 4.6 yd³ larger-bucket than 92% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2245 | |
| Engine Model | D 924 TI-E A2 | |
| Gross Power | 198hp | 147.7kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 591.6lb ft | 802Nm |
| Displacement | 405.2cu in | 6.7L |
| Torque Measured @ | 1200rpm | |
| Aspiration | Inline engine, water-cooled exhaust-turbo charged with intercooler |
02 Operational Specification
| Operating Weight | 38140lb | 17300kg |
|---|---|---|
| Fuel Capacity | 68.7gal | 260L |
| Hydraulic System Fluid Capacity | 58.2gal | 220L |
| Engine Oil Fluid Capacity | 5.5gal | 20.5L |
| Front Axle/Diff Fluid Capacity | 13.5gal | 51L |
| Rear Axle/Diff Fluid Capacity | 7.4gal | 28L |
| Static Tipping Weight | 30699.4lb | 13925kg |
| Turning Radius | 20.9ft in | 6360mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 55amps | |
| Rear Axle Oscillation | 26degrees | |
| Tire Size | 23.5 R 25 |
03 Transmission Specification
| Transmission Type | Stepless hydrostatic travel drive 2plus2 | |
|---|---|---|
| Number Of Forward Gears | 3 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.9mph | 40km/h |
| Max Speed - Reverse | 24.9mph | 40km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 4786.3psi | 33000kPa |
|---|---|---|
| Pump Flow Capacity | 60.8gal/min | 230L/min |
| Raise Time | 5.5sec | |
| Dump Time | 2.3sec | |
| Lower Time | 2.7sec | |
| Pump Type | Load-sensing variable axial piston pump with output control and pressure cutoff |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 10.13ft in | 3085mm |
|---|---|---|
| Bucket Capacity - Heaped | 4.58yd3 | 3.5m3 |
| Bucket Width | 8.86ft in | 2700mm |
| Breakout Force | 29225.17lb | 130kN |
06 Dimensions Dimensions
| Ground Clearance | 1.74ft in | 530mm |
|---|---|---|
| Length With Bucket On Ground | 26.68ft in | 8130mm |
| Height To Top Of Cab | 11.01ft in | 3355mm |
| Wheelbase | 10.34ft in | 3150mm |
| Hinge Pin - Max Height | 13.72ft in | 4180mm |
| Reach At Max Lift And Dump | 3.52ft in | 1070mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.