Specification sheet Wheel Loader Ref liebherr-l542-2plus1-wheel-loader
Liebherr L542 2plus1
The Liebherr L542 2plus1 is a wheel loader with an operating weight of 28,750 lb (13,040.79 kg), a 140.81 hp engine, and a 3.54 yd³ (2.7 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
28,750lb
13,040.79kg
Engine power
140.81hp
105kW
Gross Power Bucket capacity
3.54yd³
2.7m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Liebherr L542 2plus1 sits in the middle of its class:
- Operating weight 28,750 lb lighter than 60% (n=439)
- Engine power 141 hp less powerful than 73% (n=408)
- Bucket capacity 3.5 yd³ larger-bucket than 61% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2245 | |
| Engine Model | D 934 S AG | |
| Gross Power | 140.9hp | 105kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 568lb ft | 770Nm |
| Displacement | 388.2cu in | 6.4L |
| Torque Measured @ | 1300rpm | |
| Aspiration | turbo-charged |
02 Operational Specification
| Operating Weight | 28750lb | 13040.8kg |
|---|---|---|
| Fuel Capacity | 45gal | 170L |
| Hydraulic System Fluid Capacity | 47.6gal | 180L |
| Engine Oil Fluid Capacity | 7.7gal | 29L |
| Front Axle/Diff Fluid Capacity | 4.4gal | 16.3L |
| Rear Axle/Diff Fluid Capacity | 4gal | 15L |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 80amps | |
| Rear Axle Oscillation | 12degrees | |
| Tire Size | 20.5R25 |
03 Transmission Specification
| Transmission Type | hydrostatic | |
|---|---|---|
| Number Of Forward Gears | 3 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.9mph | 40km/h |
| Max Speed - Reverse | 24.9mph | 40km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 4786.3psi | 33000kPa |
|---|---|---|
| Pump Flow Capacity | 37gal/min | 140L/min |
| Raise Time | 5.9sec | |
| Dump Time | 1.6sec | |
| Lower Time | 4sec | |
| Pump Type | Load-sensing variable axial piston pump with output and flow control, and pressure cut-off in the control block |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.34ft in | 2845mm |
|---|---|---|
| Breakout Force | _- | 105kN |
| Bucket Capacity - Heaped | 3.54yd3 | 2.7m3 |
| Bucket Width | 8.21ft in | 2500mm |
06 Dimensions Dimensions
| Ground Clearance | 1.61ft in | 490mm |
|---|---|---|
| Length With Bucket On Ground | 23.71ft in | 7225mm |
| Height To Top Of Cab | 10.67ft in | 3250mm |
| Wheelbase | 9.77ft in | 2975mm |
| Hinge Pin - Max Height | 12.9ft in | 3930mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.