Specification sheet Wheel Loader Ref liebherr-l526-wheel-loader
Liebherr L526
The Liebherr L526 is a wheel loader with an operating weight of 24,800 lb (11,249.1 kg), a 135 hp engine, a 2.7 yd³ (2.07 m³) bucket, and a dig depth of 5 ft (1,524 mm).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
24,800lb
11,249.1kg
Engine power
135hp
100.7kW
Net Power Bucket capacity
2.7yd³
2.07m³
Dig depth
5ft
1,524mm
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Liebherr L526 sits below the median for its class:
- Operating weight 24,800 lb lighter than 84% (n=439)
- Engine power 135 hp less powerful than 80% (n=408)
- Bucket capacity 2.7 yd³ smaller-bucket than 71% (n=387)
◇Scale drawingdrawn to scale · mm
01 Electrical System Specification
| Alternator | 24/100 (V/A) | |
|---|---|---|
| Voltage | 24 VV | |
| Starter | 24/10.5 (V/HP) | |
| Battery | 2 x 135 Ah |
02 Engine Specification
| Fuel Injection | Electronic Common Rail high-pressure injection | |
|---|---|---|
| Number Of Cylinders | 4 | |
| Engine Model | 4045HLC07 | |
| Net Power | 135hp | 100.7kw |
| Air Cleaner | Dry type filter with main and safety element, pre-cleaner, service indicator on the Liebherr display | |
| Gross Power | 138hp | 103kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 404 lb ft | |
| Displacement | 275cu in | 4.6L |
| Torque Measured @ | 1500rpm | |
| Aspiration | Water-cooled turbocharged in-line engine with cooled exhaust gas recirculation, exhaust after-treatment with a closed diesel particle filter system and SCR technology | |
| Bore | 4.2in | 106mm |
| Stroke | 5in | 127mm |
03 Operational Specification
| Operating Weight | 24800lb | 11249.1kg |
|---|---|---|
| Fuel Capacity | 54.2gal | 205.2L |
| Hydraulic System Fluid Capacity | 44.9gal | 170L |
| Engine Oil Fluid Capacity | 5.8gal | 22L |
| Cooling System Fluid Capacity | 8.2gal | 31.1L |
| Hydraulic Fluid Capacity | 25.1gal | 95.1L |
| Transmission Fluid Capacity | 0.7gal | 2.7L |
| Front Axle/Diff Fluid Capacity | 4.2gal | 15.9L |
| Rear Axle/Diff Fluid Capacity | 4.2gal | 15.9L |
| Static Tipping Weight | 16975lb | 7699.8kg |
| Turning Radius | 19.6ft in | 5974.1mm |
| Tire Size | 17.5R25 L3 |
04 Transmission Specification
| Number Of Forward Gears | 3 | |
|---|---|---|
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.9mph | 40.1km/h |
| Max Speed - Reverse | 24.9mph | 40.1km/h |
05 Hydraulic System Specification
| Max Operating Pressure | 4786 psi | |
|---|---|---|
| Relief Valve Setting | 4351.2psi | 30000kPa |
| Pump Flow Capacity | 36gal/min | 136.3L/min |
| Raise Time | 5.3sec | |
| Dump Time | 2.1sec | |
| Lower Time | 3.6sec | |
| Pump Type | “Load-sensing” variable axial piston pump with output and flow control, and pressure cut-off in the control block |
06 Bucket Dimensions
| Dump Clearance At Max Raise | 9.1ft in | 2773.68mm |
|---|---|---|
| Arm Length | 8.5ft in | 2590.81mm |
| Breakout Force | 22480lb | 100kN |
| Bucket Capacity - Heaped | 2.7yd3 | 2.07m3 |
| Bucket Width | 8.2ft in | 2499.36mm |
| Digging Depth | 5ft in | 1524mm |
07 Dimensions Dimensions
| Ground Clearance | 1.6ft in | 487.68mm |
|---|---|---|
| Length With Bucket On Ground | 25.3ft in | 7711.44mm |
| Height To Top Of Cab | 10.6ft in | 3230.88mm |
| Wheelbase | 9.7ft in | 2956.56mm |
| Hinge Pin - Max Height | 12.8ft in | 3901.44mm |
| Reach At Max Lift And Dump | 3.1ft in | 944.88mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.