Specification sheet Wheel Loader Ref komatsu-wa320pz-6-quick-coupler-wheel-loader

Komatsu WA320PZ-6 Quick Coupler

The Komatsu WA320PZ-6 Quick Coupler is a wheel loader with an operating weight of 34,050.4 lb (15,445 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
34,050.4lb
15,445kg

Where it sits in its classpercentile · small wheel loaders

Among 439 small wheel loaders (22,000–45,000 lb), the Komatsu WA320PZ-6 Quick Coupler sits above the median for its class:

  • Operating weight 34,050 lb heavier than 63% (n=439)

Not positioned on engine power, bucket capacity — withheld or unpublished for this machine.

01 Tyres Specification

Standard Fitment Size 20.5 R25 L3

02 Steering System Specification

Steering System Type Full-hydraulic power steering
Minimum Turning Radius At The Centre Of Outside Tire 17.7ft in 5380mm
Steering Angle 38.5degrees

03 Engine Specification

Horsepower, Gross-Sae J1995 170.8hp 127.3kw
Horsepower, Net-Iso 9249 167.7hp 125kw
Horsepower, Net-Sae J1349 167.7hp 125kw
Fan Drive Method Hydraulic
Lubrication Method Gear pump, force-lubrication
Filter Full-flow type
Number Of Cylinders 6
Engine Model Komatsu SAA6D107E-1
Engine Type Water-cooled, 4-cycle
Air Cleaner Dry type with double elements and dust evacuator, plus dust indicator
Governor All-speed, electronic
Rated Power ​2000
Displacement 408.3cu in 6.7L
Aspiration Turbocharged, aftercooled
Fuel Type Direct injection
Bore 4.3in 107mm
Stroke 4.9in 124mm

04 Driveline Specification

Maximum Speeds, Fwd / Rev 23.7mph 38km/h
Brake Hydraulic, Wet disc
Ride Control System Standard
Number Of Speeds - Forward 4
Number Of Speeds - Reverse 4
Transmission Type Hydrostatic

05 Capacities Specification

Fuel Tank 64.8gal 245L
Cooling System 6.7gal 25L
Hydraulic System 23.6gal 89L
Engine Oil 6.1gal 23L
Torque Converter, Transmission And Retarder Cooling 1.8gal 6.5L
Axle Each (Front & Rear) 6.4gal 24L

06 Operational Specification

Bucket Capacity Range – Sae On request
Standard Bucket Capacity – Sae 3.6yd3 2.7m3
Bucket Description GP Bucket, bolt on edge
Static Tipping Load,Full Turn 20403.8lb 9255kg
Breakout Force 14410 kgf
Dump Clearance, @45 Degrees Dump Angle 9.2ft in 2800mm
Dump Reach, @45 Degrees Dump Angle 3.8ft in 1130mm
Bucket Width 9ft in 2740mm
Bucket Link Type Z-Bar

07 Transmission Specification

Transmission Type Hydrostatic, 1 pump, 2 motors with speed range select

08 Weights Specification

Operating Weight 34050.4lb 15445kg

09 Hydraulic System Specification

Steering Pump Type Gear
Loader Control Type Gear
Number Of Cylinders 2
Bore 2.8in 70mm
Hydraulic Pump Gear type pump
Steering System Relief Valve Setting 2990psi 20615.4kPa
Loader Control Relief Valve Setting 3000psi 20684.3kPa
Steering System Capacity 45.5gal/min 172L/min
Loader Control Capacity 16.2gal/min 61L/min
Control Valve 3-spool type
Control Positions Boom Raise, hold, lower, and float
Control Positions Bucket Tilt-back, hold, and dump
Hydraulic Cylinders Type Double-acting, piston type
Stroke 453 mm
Raise Time 5.6sec
Dump Time 1.9sec
Lower Time 3.3sec

10 Final Drive Specification

Reduction Gear Spiral bevel gear
Differential Gear Torque proportioning
Final Reduction Gear Planetary gear, single reduction
Drive System Four-wheel drive
Front Fixed, semi-floating
Rear Center-pin support, semi-floating, 24˚ total oscillation

11 Brakes Specification

Parking Brake Wet, multi-disc brake on transfer output shaft
Service Brake Hydraulically actuated, wet disc brakes actuate on four wheels
Emergency Brake Parking brake is commonly used

12 Dimensions Dimensions

Ground Clearance 1.4ft in 425mm
Height To Top Of Cab 10.5ft in 3200mm
Wheelbase 119.3in 3030mm
Length 7770 mm
Overall Height, Rops Cab 125.99in 3200mm
Overall Height, Top Of Stack 114.77in 2915mm
Standard Tire 20.5-25-12PR(L2)
Tread 80.71in 2050mm
Width Over Tyres 101.97in 2590mm
Hinge Pin Height, Maximum Height 157.68in 4005mm
Hitch Heigh 43.12in 1095mm

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.