Specification sheet Wheel Loader Ref komatsu-wa250pt-5-wheel-loader
Komatsu WA250PT-5
The Komatsu WA250PT-5 is a wheel loader with an operating weight of 28,219.18 lb (12,800 kg), a 134 hp engine, and a 2.62 yd³ (2 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
28,219.18lb
12,800kg
Engine power
134hp
100kW
Net Power Bucket capacity
2.62yd³
2m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Komatsu WA250PT-5 sits below the median for its class:
- Operating weight 28,220 lb lighter than 65% (n=439)
- Engine power 134 hp less powerful than 81% (n=408)
- Bucket capacity 2.6 yd³ smaller-bucket than 76% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2238 | |
| Engine Model | SAA6 D102 E | |
| Net Power | 134hp | 100kw |
| Gross Power | 139hp | 103.7kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 455.9lb ft | 618Nm |
| Displacement | 360.1cu in | 5.9L |
| Torque Measured @ | 1400rpm | |
| Aspiration | Turbocharged |
02 Operational Specification
| Operating Weight | 28219.2lb | 12800kg |
|---|---|---|
| Fuel Capacity | 47.9gal | 181L |
| Hydraulic System Fluid Capacity | 17.7gal | 67L |
| Engine Oil Fluid Capacity | 5.2gal | 19.5L |
| Cooling System Fluid Capacity | 4.7gal | 17.5L |
| Transmission Fluid Capacity | 1.9gal | 6.9L |
| Front Axle/Diff Fluid Capacity | 4.8gal | 18L |
| Rear Axle/Diff Fluid Capacity | 4.8gal | 18L |
| Static Tipping Weight | 23078lb | 10468kg |
| Turning Radius | 17.2ft in | 5240mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 60amps | |
| Rear Axle Oscillation | 30degrees | |
| Tire Size | 20.5 R 25 |
03 Transmission Specification
| Transmission Type | Electronically controlled hydrostatic | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 23.7mph | 38km/h |
| Max Speed - Reverse | 23.7mph | 38km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3045.8psi | 21000kPa |
|---|---|---|
| Pump Flow Capacity | 43.1gal/min | 163L/min |
| Raise Time | 6.3sec | |
| Dump Time | 3.3sec | |
| Lower Time | 1.7sec | |
| Pump Type | Gear Pump |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.47ft in | 2885mm |
|---|---|---|
| Bucket Capacity - Heaped | 2.62yd3 | 2m3 |
| Bucket Capacity - Struck | 2.1yd3 | 1.6m3 |
| Bucket Width | 8.37ft in | 2550mm |
| Breakout Force | 27201.88lb | 121kN |
06 Dimensions Dimensions
| Ground Clearance | 1.51ft in | 460mm |
|---|---|---|
| Length With Bucket On Ground | 23.87ft in | 7275mm |
| Width Over Tires | 8.11ft in | 2470mm |
| Height To Top Of Cab | 10.63ft in | 3240mm |
| Wheelbase | 9.52ft in | 2900mm |
| Hinge Pin - Max Height | 13ft in | 3960mm |
| Reach At Max Lift And Dump | 3.56ft in | 1085mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.