Specification sheet Wheel Loader Ref komatsu-wa180-3pt-wheel-loader
Komatsu WA180-3PT
The Komatsu WA180-3PT is a wheel loader with an operating weight of 22,586.36 lb (10,245 kg), a 112 hp engine, and a 2.1 yd³ (1.6 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
22,586.36lb
10,245kg
Engine power
112hp
83.52kW
Gross Power Bucket capacity
2.1yd³
1.6m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Komatsu WA180-3PT sits at the compact end of its class:
- Operating weight 22,590 lb lighter than 96% (n=439)
- Engine power 112 hp less powerful than 97% (n=408)
- Bucket capacity 2.1 yd³ smaller-bucket than 95% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2238 | |
| Engine Model | S6D102-E1 | |
| Gross Power | 112hp | 83.6kw |
| Power Measured @ | 2400rpm | |
| Max Torque | 307.6lb ft | 417Nm |
| Displacement | 360.1cu in | 5.9L |
| Aspiration | Turbo |
02 Operational Specification
| Operating Weight | 22586.4lb | 10245kg |
|---|---|---|
| Fuel Capacity | 45gal | 170L |
| Hydraulic System Fluid Capacity | 10.9gal | 41L |
| Engine Oil Fluid Capacity | 5.2gal | 19.5L |
| Cooling System Fluid Capacity | 5.7gal | 21.5L |
| Transmission Fluid Capacity | 6.3gal | 23.5L |
| Front Axle/Diff Fluid Capacity | 3.7gal | 14L |
| Rear Axle/Diff Fluid Capacity | 3.7gal | 14L |
| Static Tipping Weight | 15167.9lb | 6880kg |
| Turning Radius | 18.3ft in | 5570mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 50amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 17.5 R 25 |
03 Transmission Specification
| Transmission Type | Fully automatic, full powershift with 'kick-down' system | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 21.5mph | 34.5km/h |
| Max Speed - Reverse | 21.8mph | 35km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3045.8psi | 21000kPa |
|---|---|---|
| Pump Flow Capacity | 38.1gal/min | 144L/min |
| Raise Time | 5sec | |
| Dump Time | 1.1sec | |
| Lower Time | 2.5sec |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 8.6ft in | 2620mm |
|---|---|---|
| Bucket Capacity - Heaped | 2.1yd3 | 1.6m3 |
| Bucket Width | 8.21ft in | 2500mm |
| Breakout Force | 19783.19lb | 88kN |
06 Dimensions Dimensions
| Ground Clearance | 1.4ft in | 425mm |
|---|---|---|
| Length With Bucket On Ground | 23.2ft in | 7070mm |
| Width Over Tires | 8.21ft in | 2500mm |
| Height To Top Of Cab | 16.61ft in | 5060mm |
| Wheelbase | 8.86ft in | 2700mm |
| Hinge Pin - Max Height | 12.34ft in | 3760mm |
| Reach At Max Lift And Dump | 3.61ft in | 1100mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.