Specification sheet Wheel Loader Ref kawasaki-90ziii-wheel-loader
Kawasaki 90ZIII
The Kawasaki 90ZIII is a wheel loader with an operating weight of 47,994.64 lb (21,770 kg), a 256 hp engine, and a 4.98 yd³ (3.8 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
47,994.64lb
21,770kg
Engine power
256hp
190.9kW
Net Power Bucket capacity
4.98yd³
3.8m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Kawasaki 90ZIII sits below the median for its class:
- Operating weight 47,990 lb lighter than 84% (n=198)
- Engine power 256 hp less powerful than 77% (n=190)
- Bucket capacity 5 yd³ smaller-bucket than 81% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | LTA-10-C290 | |
| Net Power | 256hp | 190.9kw |
| Power Measured @ | 2100rpm | |
| Max Torque | 832lb ft | 1128.1Nm |
| Displacement | 611cu in | 10.1L |
| Torque Measured @ | 1300rpm | |
| Aspiration | turbocharged & after cooled |
02 Operational Specification
| Operating Weight | 47994.7lb | 21770kg |
|---|---|---|
| Fuel Capacity | 81.9gal | 310L |
| Hydraulic System Fluid Capacity | 43.6gal | 165L |
| Engine Oil Fluid Capacity | 11.7gal | 44L |
| Cooling System Fluid Capacity | 14.8gal | 56L |
| Transmission Fluid Capacity | 15.9gal | 60L |
| Front Axle/Diff Fluid Capacity | 14.6gal | 55L |
| Rear Axle/Diff Fluid Capacity | 14.6gal | 55L |
| Static Tipping Weight | 35274lb | 16000kg |
| Turning Radius | 22.4ft in | 6825mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 75amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 26.5-25-20PR (L-3) |
03 Transmission Specification
| Transmission Type | full power shift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 20.5mph | 33km/h |
| Max Speed - Reverse | 20.8mph | 33.5km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3000psi | 20684.3kPa |
|---|---|---|
| Pump Flow Capacity | 37gal/min | 140.1L/min |
| Raise Time | 6.1sec | |
| Dump Time | 1.6sec | |
| Lower Time | 3sec | |
| Pump Type | gear type |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.91ft in | 3020mm |
|---|---|---|
| Bucket Capacity - Heaped | 4.98yd3 | 3.8m3 |
| Bucket Capacity - Struck | 4.26yd3 | 3.25m3 |
| Bucket Width | 10.18ft in | 3100mm |
| Breakout Force | 43870lb | 195.15kN |
06 Dimensions Dimensions
| Ground Clearance | 1.69ft in | 515mm |
|---|---|---|
| Length With Bucket On Ground | 27.47ft in | 8370mm |
| Width Over Tires | 9.62ft in | 2930mm |
| Height To Top Of Cab | 11.59ft in | 3530mm |
| Wheelbase | 11.16ft in | 3400mm |
| Hinge Pin - Max Height | 13.98ft in | 4260mm |
| Reach At Max Lift And Dump | 4.07ft in | 1240mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.