Specification sheet Wheel Loader Ref kawasaki-80zv-2-wheel-loader
Kawasaki 80ZV-2
The Kawasaki 80ZV-2 is a wheel loader with an operating weight of 39,308 lb (17,829.81 kg), a 198 hp engine, and a 4.19 yd³ (3.2 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
39,308lb
17,829.81kg
Engine power
198hp
147.7kW
Net Power Bucket capacity
4.19yd³
3.2m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Kawasaki 80ZV-2 sits above the median for its class:
- Operating weight 39,310 lb heavier than 82% (n=439)
- Engine power 198 hp more powerful than 75% (n=408)
- Bucket capacity 4.2 yd³ larger-bucket than 82% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | QSC8.3 | |
| Net Power | 198hp | 147.7kw |
| Power Measured @ | 2200rpm | |
| Max Torque | 645lb ft | 874.6Nm |
| Displacement | 504cu in | 8.3L |
| Torque Measured @ | 1500rpm | |
| Aspiration | turbocharged |
02 Operational Specification
| Operating Weight | 39308lb | 17829.9kg |
|---|---|---|
| Fuel Capacity | 76.7gal | 290L |
| Hydraulic System Fluid Capacity | 42.3gal | 160L |
| Engine Oil Fluid Capacity | 8gal | 30L |
| Cooling System Fluid Capacity | 15.9gal | 60L |
| Transmission Fluid Capacity | 11.9gal | 45L |
| Front Axle/Diff Fluid Capacity | 14.6gal | 55L |
| Rear Axle/Diff Fluid Capacity | 14.6gal | 55L |
| Static Tipping Weight | 30600lb | 13880kg |
| Turning Radius | 21ft in | 6375mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 70amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 23.5x25-16PR (L-3) |
03 Transmission Specification
| Transmission Type | full powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 22.9mph | 36.9km/h |
| Max Speed - Reverse | 23.2mph | 37.4km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3000psi | 20684.3kPa |
|---|---|---|
| Pump Flow Capacity | 19gal/min | 72L/min |
| Raise Time | 6.2sec | |
| Dump Time | 1.4sec | |
| Lower Time | 3.4sec | |
| Pump Type | gear type |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.72ft in | 2960mm |
|---|---|---|
| Bucket Capacity - Heaped | 4.19yd3 | 3.2m3 |
| Bucket Capacity - Struck | 3.54yd3 | 2.7m3 |
| Bucket Width | 9.19ft in | 2800mm |
| Breakout Force | 36193lb | 161kN |
06 Dimensions Dimensions
| Ground Clearance | 1.53ft in | 465mm |
|---|---|---|
| Length With Bucket On Ground | 26.25ft in | 8000mm |
| Width Over Tires | 8.8ft in | 2680mm |
| Height To Top Of Cab | 11.32ft in | 3448mm |
| Wheelbase | 10.5ft in | 3200mm |
| Hinge Pin - Max Height | 13.44ft in | 4095mm |
| Reach At Max Lift And Dump | 3.71ft in | 1130mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.