Specification sheet Wheel Loader Ref kawasaki-80ziv-2-wheel-loader
Kawasaki 80ZIV-2
The Kawasaki 80ZIV-2 is a wheel loader with an operating weight of 35,825.12 lb (16,250 kg), a 178 hp engine, and a 3.67 yd³ (2.8 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
35,825.12lb
16,250kg
Engine power
178hp
132.74kW
Gross Power Bucket capacity
3.67yd³
2.8m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Kawasaki 80ZIV-2 sits above the median for its class:
- Operating weight 35,830 lb heavier than 69% (n=439)
- Engine power 178 hp more powerful than 63% (n=408)
- Bucket capacity 3.7 yd³ larger-bucket than 66% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | C-8.3-C | |
| Gross Power | 178hp | 132.8kw |
| Power Measured @ | 2200rpm | |
| Max Torque | 557lb ft | 755.2Nm |
| Displacement | 504.5cu in | 8.3L |
| Torque Measured @ | 1500rpm | |
| Aspiration | turbocharged |
02 Operational Specification
| Operating Weight | 35825.2lb | 16250kg |
|---|---|---|
| Fuel Capacity | 63.5gal | 240L |
| Hydraulic System Fluid Capacity | 38.4gal | 145L |
| Engine Oil Fluid Capacity | 6.7gal | 25L |
| Cooling System Fluid Capacity | 14.6gal | 55L |
| Transmission Fluid Capacity | 11.9gal | 45L |
| Front Axle/Diff Fluid Capacity | 14.6gal | 55L |
| Rear Axle/Diff Fluid Capacity | 14.6gal | 55L |
| Static Tipping Weight | 27778.3lb | 12600kg |
| Turning Radius | 20.9ft in | 6340mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 70amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 23.5x25-16PR (L-3) |
03 Transmission Specification
| Transmission Type | full powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 21.7mph | 35km/h |
| Max Speed - Reverse | 22mph | 35.5km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3000psi | 20684.3kPa |
|---|---|---|
| Pump Flow Capacity | 17.2gal/min | 65.2L/min |
| Raise Time | 6.2sec | |
| Dump Time | 1.4sec | |
| Lower Time | 3.4sec | |
| Pump Type | gear type |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.26ft in | 2820mm |
|---|---|---|
| Bucket Capacity - Heaped | 3.67yd3 | 2.8m3 |
| Bucket Capacity - Struck | 3.27yd3 | 2.5m3 |
| Bucket Width | 9.19ft in | 2800mm |
| Breakout Force | 34390lb | 152.98kN |
06 Dimensions Dimensions
| Ground Clearance | 1.51ft in | 460mm |
|---|---|---|
| Length With Bucket On Ground | 25.55ft in | 7785mm |
| Width Over Tires | 8.81ft in | 2685mm |
| Height To Top Of Cab | 11.08ft in | 3375mm |
| Wheelbase | 10.5ft in | 3200mm |
| Hinge Pin - Max Height | 12.98ft in | 3955mm |
| Reach At Max Lift And Dump | 3.83ft in | 1165mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.