John Deere JD24A
The John Deere JD24A is a skid steer loader with an operating weight of 5,483 lb (2,487 kg), a 37 hp engine, a rated operating capacity of 1,349.23 lb (612 kg), and a tipping load of 2,700.7 lb (1,225.02 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the John Deere JD24A sits below the median for its class:
- Operating weight 5,480 lb lighter than 79% (n=334)
- Engine power 37 hp less powerful than 90% (n=335)
- Rated operating capacity 1,350 lb lower-rated than 84% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Engine Make | 2356 | |
|---|---|---|
| Engine Model | Y-112, 4-cylinder, 4-stroke | |
| Net Power | 37hp | 27.6kw |
| Aspiration | Hydrostatic | |
| Displacement | 112cu in | 1.9L |
02 Operational Specification
| Operational Weight | 5483lb | 2487kg |
|---|---|---|
| Fuel Capacity | 24gal | 90.8L |
| Cooling System Fluid Capacity | 3.1gal | 11.4L |
| Hydraulic System Fluid Capacity | 18gal | 68.1L |
| Max Speed | 6.5mph | 10.5km/h |
| Operating Speed | -6.5mph | -10.5km/h |
| Tire Size | 10-16.5,steel-cap,4PR/6.50-16,lug tread,solid rubber | |
| Operating Voltage | 12V |
03 Loader Specification
| Operating Load Rating | 1349.3lb | 612kg |
|---|---|---|
| Bucket Capacity | 0.4yd3 | 0.3m3 |
04 Hydraulic Specification
| Pump Type | Pressure system with full-flow filter |
|---|
05 Dimensions Dimensions
| Length With Bucket | 9.83ft in | 2990mm |
|---|---|---|
| Ground Clearance | 7in | 178mm |
| Height To Top Of Cab | 9ft in | 2743.2mm |
| Wheelbase | 2.92ft in | 889mm |
| Length W/O Bucket | 7.09ft in | 2160mm |
| Clearance At Max Lift And Dump | 7ft in | 2130mm |
| Reach At Max Lift And Dump ‡ — value corrected — the source published it under the wrong unit | 16.5in | 418mm |
| Turning Radius From Center - Machine Rear ‡ — value corrected — the source published it under the wrong unit | 52.4in | 1330mm |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Corrected value. The source published these figures under the wrong unit. The metric figure is authoritative and the imperial value shown here is derived from it.
- Reach At Max Lift And Dump: shown as 16.5 in (source stated a value inconsistent with its own metric figure of 418 mm)
- Turning Radius From Center - Machine Rear: shown as 52.4 in (source stated a value inconsistent with its own metric figure of 1330 mm)
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.