Specification sheet Wheel Loader Ref john-deere-824k-high-lift-wheel-loader
John Deere 824K High-Lift
The John Deere 824K High-Lift is a wheel loader with an operating weight of 56,634.55 lb (25,689 kg), a 333 hp engine, and a 6.02 yd³ (4.6 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
56,634.55lb
25,689kg
Engine power
333hp
248.4kW
Net Power Bucket capacity
6.02yd³
4.6m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the John Deere 824K High-Lift sits in the middle of its class:
- Operating weight 56,630 lb heavier than 60% (n=198)
- Engine power 333 hp more powerful than 85% (n=190)
- Bucket capacity 6 yd³ larger-bucket than 70% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2240 | |
| Engine Model | 6135H, Tier III certified | |
| Net Power | 333hp | 248.4kw |
| Power Measured @ | 1600rpm | |
| Max Torque | 1194lb ft | 1618.9Nm |
| Displacement | 824cu in | 13.6L |
| Torque Measured @ | 900rpm | |
| Aspiration | Turbocharged charge air cooled | |
| Torque Rise | 59% |
02 Operational Specification
| Operating Weight | 56634.6lb | 25689kg |
|---|---|---|
| Fuel Capacity | 124.1gal | 469.4L |
| Hydraulic System Fluid Capacity | 42.1gal | 159L |
| Engine Oil Fluid Capacity | 10.1gal | 37.9L |
| Cooling System Fluid Capacity | 12.6gal | 47.4L |
| Transmission Fluid Capacity | 7.4gal | 27.9L |
| Front Axle/Diff Fluid Capacity | 12.2gal | 45.9L |
| Rear Axle/Diff Fluid Capacity | 12.2gal | 45.9L |
| Static Tipping Weight | 37983.5lb | 17229kg |
| Turning Radius | 19.5ft in | 5920mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 80amps | |
| Rear Axle Oscillation | 26degrees | |
| Tire Size | 26.5 R 25 |
03 Transmission Specification
| Transmission Type | Countershaft, powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.9mph | 40km/h |
| Max Speed - Reverse | 18.8mph | 30.1km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3650psi | 25165.9kPa |
|---|---|---|
| Pump Flow Capacity | 135.6gal/min | 513L/min |
| Raise Time | 5.9sec | |
| Dump Time | 1.3sec | |
| Lower Time | 2.6sec | |
| Pump Type | two variable displacement, load-sensing axial piston |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 11.91ft in | 3630mm |
|---|---|---|
| Bucket Capacity - Heaped | 6.02yd3 | 4.6m3 |
| Bucket Capacity - Struck | 5.24yd3 | 4m3 |
| Bucket Width | 10.73ft in | 3270mm |
| Breakout Force | 39570lb | 176.02kN |
06 Dimensions Dimensions
| Ground Clearance | 1.51ft in | 460mm |
|---|---|---|
| Length With Bucket On Ground | 32.06ft in | 9770mm |
| Width Over Tires | 10.06ft in | 3065mm |
| Height To Top Of Cab | 11.49ft in | 3500mm |
| Wheelbase | 11.36ft in | 3460mm |
| Hinge Pin - Max Height | 15.92ft in | 4850mm |
| Reach At Max Lift And Dump | 5.35ft in | 1630mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.