Specification sheet Wheel Loader Ref john-deere-744k-z-bar-wheel-loader
John Deere 744K Z-Bar
The John Deere 744K Z-Bar is a wheel loader with an operating weight of 53,312.19 lb (24,182 kg), a 304 hp engine, and a 5.24 yd³ (4 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
53,312.19lb
24,182kg
Engine power
304hp
226.7kW
Net Power Bucket capacity
5.24yd³
4m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the John Deere 744K Z-Bar sits in the middle of its class:
- Operating weight 53,310 lb heavier than 50% (n=198)
- Engine power 304 hp more powerful than 70% (n=190)
- Bucket capacity 5.2 yd³ smaller-bucket than 72% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2240 | |
| Engine Model | 6090H, Tier III certified | |
| Net Power | 304hp | 226.7kw |
| Power Measured @ | 1500rpm | |
| Max Torque | 1074lb ft | 1456.2Nm |
| Displacement | 548cu in | 9L |
| Torque Measured @ | 1400rpm | |
| Aspiration | Turbocharged charge air cooled | |
| Torque Rise | 47% |
02 Operational Specification
| Operating Weight | 53312.2lb | 24182kg |
|---|---|---|
| Fuel Capacity | 123.9gal | 469L |
| Hydraulic System Fluid Capacity | 42.1gal | 159L |
| Engine Oil Fluid Capacity | 9gal | 34L |
| Cooling System Fluid Capacity | 11.9gal | 45L |
| Transmission Fluid Capacity | 7.4gal | 27.9L |
| Front Axle/Diff Fluid Capacity | 12.2gal | 46L |
| Rear Axle/Diff Fluid Capacity | 12.2gal | 46L |
| Static Tipping Weight | 43922.7lb | 19923kg |
| Turning Radius | 20.7ft in | 6280mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 80amps | |
| Rear Axle Oscillation | 26degrees | |
| Tire Size | 26.5 R 25 |
03 Transmission Specification
| Transmission Type | Countershaft, powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.9mph | 40km/h |
| Max Speed - Reverse | 18.8mph | 30.2km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3288psi | 22670kPa |
|---|---|---|
| Pump Flow Capacity | 136.1gal/min | 515L/min |
| Raise Time | 5.9sec | |
| Dump Time | 1.4sec | |
| Lower Time | 2.8sec | |
| Pump Type | two variable displacement, load-sensing axial piston |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.98ft in | 3040mm |
|---|---|---|
| Bucket Capacity - Heaped | 5.24yd3 | 4m3 |
| Bucket Capacity - Struck | 4.45yd3 | 3.4m3 |
| Bucket Width | 10.73ft in | 3270mm |
| Breakout Force | 42805lb | 190.41kN |
06 Dimensions Dimensions
| Ground Clearance | 1.51ft in | 460mm |
|---|---|---|
| Length With Bucket On Ground | 29.57ft in | 9010mm |
| Width Over Tires | 9.71ft in | 2957mm |
| Height To Top Of Cab | 11.49ft in | 3500mm |
| Wheelbase | 11.36ft in | 3460mm |
| Hinge Pin - Max Height | 14.05ft in | 4280mm |
| Reach At Max Lift And Dump | 4.04ft in | 1230mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.