Specification sheet Wheel Loader Ref john-deere-744e-wheel-loader
John Deere 744E
The John Deere 744E is a wheel loader with an operating weight of 46,310 lb (21,006 kg), a 250 hp engine, and a 5 yd³ (3.8 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
46,310lb
21,006kg
Engine power
250hp
186.5kW
Net Power Bucket capacity
5yd³
3.8m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the John Deere 744E sits at the compact end of its class:
- Operating weight 46,310 lb lighter than 92% (n=198)
- Engine power 250 hp less powerful than 82% (n=190)
- Bucket capacity 5 yd³ smaller-bucket than 78% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2240 | |
| Engine Model | 6101AT | |
| Net Power | 250hp | 186.5kw |
| Gross Power | 260hp | 193.9kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 750lb ft | 1016.9Nm |
| Displacement | 619cu in | 10.2L |
| Torque Measured @ | 1700rpm | |
| Aspiration | Turbocharged with Aftercooler | |
| Torque Rise | 34% |
02 Operational Specification
| Operating Weight | 46310lb | 21006kg |
|---|---|---|
| Fuel Capacity | 87gal | 330L |
| Hydraulic System Fluid Capacity | 42.6gal | 161L |
| Engine Oil Fluid Capacity | 8.5gal | 32L |
| Cooling System Fluid Capacity | 14.6gal | 55L |
| Transmission Fluid Capacity | 10.1gal | 38L |
| Front Axle/Diff Fluid Capacity | 8.8gal | 33L |
| Rear Axle/Diff Fluid Capacity | 9.3gal | 35L |
| Static Tipping Weight | 33755lb | 15311kg |
| Turning Radius | 20.2ft in | 6140mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 50amps | |
| Rear Axle Oscillation | 26degrees | |
| Tire Size | 23.5-25 |
03 Transmission Specification
| Transmission Type | Power Shift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 25.8mph | 41.6km/h |
| Max Speed - Reverse | 28mph | 45.1km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3129psi | 21573.7kPa |
|---|---|---|
| Pump Flow Capacity | 82gal/min | 310.5L/min |
| Raise Time | 6.4sec | |
| Dump Time | 1.5sec | |
| Lower Time | 3.5sec | |
| Pump Type | Gear |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.81ft in | 2988mm |
|---|---|---|
| Bucket Capacity - Heaped | 5yd3 | 3.8m3 |
| Bucket Capacity - Struck | 4.3yd3 | 3.3m3 |
| Bucket Width | 9.98ft in | 3040mm |
| Breakout Force | 42463lb | 189kN |
06 Dimensions Dimensions
| Ground Clearance | 1.69ft in | 515mm |
|---|---|---|
| Length With Bucket On Ground | 26.32ft in | 8020mm |
| Width Over Tires | 9.26ft in | 2820mm |
| Height To Top Of Cab | 11.62ft in | 3540mm |
| Wheelbase | 11.16ft in | 3400mm |
| Hinge Pin - Max Height | 13.65ft in | 4160mm |
| Reach At Max Lift And Dump | 4.18ft in | 1272mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.