Specification sheet Wheel Loader Ref john-deere-724k-z-bar-wheel-loader
John Deere 724K Z-Bar
The John Deere 724K Z-Bar is a wheel loader with an operating weight of 42,174.43 lb (19,130 kg), a 264 hp engine, and a 4.71 yd³ (3.6 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
42,174.43lb
19,130kg
Engine power
264hp
196.9kW
Net Power Bucket capacity
4.71yd³
3.6m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the John Deere 724K Z-Bar sits at the heavy end of its class:
- Operating weight 42,170 lb heavier than 92% (n=439)
- Engine power 264 hp more powerful than 99% (n=408)
- Bucket capacity 4.7 yd³ larger-bucket than 94% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2240 | |
| Engine Model | 6090H, Tier III certified | |
| Net Power | 264hp | 196.9kw |
| Power Measured @ | 1800rpm | |
| Max Torque | 852lb ft | 1155.2Nm |
| Displacement | 548cu in | 9L |
| Torque Measured @ | 1300rpm | |
| Aspiration | Turbocharged charge air cooled | |
| Torque Rise | 36% |
02 Operational Specification
| Operating Weight | 42174.5lb | 19130kg |
|---|---|---|
| Fuel Capacity | 93gal | 352L |
| Hydraulic System Fluid Capacity | 29.1gal | 110L |
| Engine Oil Fluid Capacity | 7.4gal | 28L |
| Cooling System Fluid Capacity | 9gal | 34L |
| Transmission Fluid Capacity | 6.4gal | 24L |
| Front Axle/Diff Fluid Capacity | 5.9gal | 22L |
| Rear Axle/Diff Fluid Capacity | 5.9gal | 22L |
| Static Tipping Weight | 36352.1lb | 16489kg |
| Turning Radius | 18.6ft in | 5640mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 80amps | |
| Rear Axle Oscillation | 26degrees | |
| Tire Size | 23.5 R25 |
03 Transmission Specification
| Transmission Type | Countershaft, powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 22.2mph | 35.6km/h |
| Max Speed - Reverse | 15.1mph | 24.2km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3650psi | 25165.9kPa |
|---|---|---|
| Pump Flow Capacity | 81.9gal/min | 310L/min |
| Raise Time | 5.5sec | |
| Dump Time | 1.2sec | |
| Lower Time | 3sec | |
| Pump Type | Variable axial piston |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.16ft in | 2790mm |
|---|---|---|
| Bucket Capacity - Heaped | 4.71yd3 | 3.6m3 |
| Bucket Capacity - Struck | 4.19yd3 | 3.2m3 |
| Bucket Width | 9.98ft in | 3040mm |
| Breakout Force | 31742lb | 141.2kN |
06 Dimensions Dimensions
| Ground Clearance | 1.35ft in | 410mm |
|---|---|---|
| Length With Bucket On Ground | 27.37ft in | 8340mm |
| Width Over Tires | 9.45ft in | 2880mm |
| Height To Top Of Cab | 11.09ft in | 3380mm |
| Wheelbase | 10.7ft in | 3260mm |
| Hinge Pin - Max Height | 13.36ft in | 4070mm |
| Reach At Max Lift And Dump | 3.71ft in | 1130mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.