Specification sheet Wheel Loader Ref john-deere-624j-powerllel-pin-on-wheel-loader
John Deere 624J Powerllel Pin-on
The John Deere 624J Powerllel Pin-on is a wheel loader with an operating weight of 33,534 lb (15,211 kg), a 198 hp engine, and a 3.5 yd³ (2.7 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
33,534lb
15,211kg
Engine power
198hp
147.7kW
Net Power Bucket capacity
3.5yd³
2.7m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the John Deere 624J Powerllel Pin-on sits above the median for its class:
- Operating weight 33,530 lb heavier than 61% (n=439)
- Engine power 198 hp more powerful than 75% (n=408)
- Bucket capacity 3.5 yd³ larger-bucket than 58% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2240 | |
| Engine Model | 6068H | |
| Net Power | 198hp | 147.7kw |
| Power Measured @ | 1800rpm | |
| Max Torque | 617lb ft | 837Nm |
| Displacement | 414cu in | 6.8L |
| Torque Measured @ | 1600rpm | |
| Aspiration | Turbocharged charge air cooled | |
| Torque Rise | 55% |
02 Operational Specification
| Operating Weight | 33534lb | 15211kg |
|---|---|---|
| Fuel Capacity | 92gal | 348L |
| Hydraulic System Fluid Capacity | 32gal | 119L |
| Engine Oil Fluid Capacity | 5.6gal | 21L |
| Cooling System Fluid Capacity | 7.2gal | 27L |
| Transmission Fluid Capacity | 6.1gal | 23L |
| Front Axle/Diff Fluid Capacity | 5.9gal | 22L |
| Rear Axle/Diff Fluid Capacity | 4.5gal | 17L |
| Static Tipping Weight | 23007lb | 10436kg |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 80amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 20.5 R25 |
03 Transmission Specification
| Transmission Type | Powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.6mph | 39.6km/h |
| Max Speed - Reverse | 16mph | 25.8km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3675psi | 25320kPa |
|---|---|---|
| Pump Flow Capacity | 60gal/min | 227L/min |
| Raise Time | 5.8sec | |
| Dump Time | 1.7sec | |
| Lower Time | 2.8sec | |
| Pump Type | Variable axial piston |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 8.92ft in | 2710mm |
|---|---|---|
| Breakout Force | 28102lb | 125kN |
| Bucket Capacity - Heaped | 3.5yd3 | 2.7m3 |
| Bucket Capacity - Struck | 3yd3 | 2.3m3 |
| Bucket Width | 8.5ft in | 2590.81mm |
06 Dimensions Dimensions
| Ground Clearance | 1.42ft in | 434mm |
|---|---|---|
| Length With Bucket On Ground | 26.17ft in | 7980mm |
| Height To Top Of Cab | 10.92ft in | 3320mm |
| Wheelbase | 9.92ft in | 3030mm |
| Hinge Pin - Max Height | 13.17ft in | 4010mm |
| Reach At Max Lift And Dump | 4.17ft in | 1270mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.