Specification sheet Wheel Loader Ref john-deere-444k-powerllel-w-q-coupler-wheel-loader
John Deere 444K Powerllel w/Q Coupler
The John Deere 444K Powerllel w/Q Coupler is a wheel loader with an operating weight of 26,618.62 lb (12,074 kg), a 128 hp engine, and a 2.49 yd³ (1.9 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
26,618.62lb
12,074kg
Engine power
128hp
95.5kW
Net Power Bucket capacity
2.49yd³
1.9m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the John Deere 444K Powerllel w/Q Coupler sits below the median for its class:
- Operating weight 26,620 lb lighter than 75% (n=439)
- Engine power 128 hp less powerful than 86% (n=408)
- Bucket capacity 2.5 yd³ smaller-bucket than 85% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2240 | |
| Engine Model | E 4045H, Tier III certified | |
| Net Power | 128hp | 95.5kw |
| Power Measured @ | 2100rpm | |
| Max Torque | 380lb ft | 515.3Nm |
| Displacement | 276cu in | 4.6L |
| Torque Measured @ | 1400rpm | |
| Aspiration | Turbocharged charge air cooled | |
| Torque Rise | 32% |
02 Operational Specification
| Operating Weight | 26618.7lb | 12074kg |
|---|---|---|
| Fuel Capacity | 64gal | 242L |
| Hydraulic System Fluid Capacity | 24.1gal | 91L |
| Engine Oil Fluid Capacity | 4.7gal | 17.5L |
| Cooling System Fluid Capacity | 5.1gal | 19L |
| Transmission Fluid Capacity | 4.9gal | 18.5L |
| Front Axle/Diff Fluid Capacity | 5.9gal | 22L |
| Rear Axle/Diff Fluid Capacity | 5.9gal | 22L |
| Static Tipping Weight | 15939.5lb | 7230kg |
| Turning Radius | 15.6ft in | 4740mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 80amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 17.5 R 25 |
03 Transmission Specification
| Transmission Type | Countershaft, powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 22.4mph | 36km/h |
| Max Speed - Reverse | 15.8mph | 25.3km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3600psi | 24821.2kPa |
|---|---|---|
| Pump Flow Capacity | 37gal/min | 140L/min |
| Raise Time | 5.9sec | |
| Dump Time | 1.1sec | |
| Lower Time | 1.9sec | |
| Pump Type | variable displacement, axial piston |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 8.47ft in | 2580mm |
|---|---|---|
| Bucket Capacity - Heaped | 2.49yd3 | 1.9m3 |
| Bucket Capacity - Struck | 2.1yd3 | 1.6m3 |
| Bucket Width | 8.34ft in | 2540mm |
| Breakout Force | 13352lb | 59.4kN |
06 Dimensions Dimensions
| Ground Clearance | 1.29ft in | 393mm |
|---|---|---|
| Length With Bucket On Ground | 23.46ft in | 7150mm |
| Width Over Tires | 7.93ft in | 2415mm |
| Height To Top Of Cab | 10.41ft in | 3170mm |
| Wheelbase | 9.06ft in | 2760mm |
| Hinge Pin - Max Height | 12.05ft in | 3670mm |
| Reach At Max Lift And Dump | 3.75ft in | 1140mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.