Specification sheet Wheel Loader Ref john-deere-444j-powerllel-pin-on-wheel-loader
John Deere 444J Powerllel Pin-on
The John Deere 444J Powerllel Pin-on is a wheel loader with an operating weight of 23,926 lb (10,853 kg), a 119 hp engine, and a 2.5 yd³ (1.9 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
23,926lb
10,853kg
Engine power
119hp
89kW
Net Power Bucket capacity
2.5yd³
1.9m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the John Deere 444J Powerllel Pin-on sits at the compact end of its class:
- Operating weight 23,930 lb lighter than 89% (n=439)
- Engine power 119 hp less powerful than 92% (n=408)
- Bucket capacity 2.5 yd³ smaller-bucket than 81% (n=387)
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2240 | |
| Engine Model | 4045H | |
| Net Power | 119hp | 89kw |
| Power Measured @ | 2200rpm | |
| Max Torque | 380lb ft | 515Nm |
| Displacement | 276cu in | 4.5L |
| Torque Measured @ | 1400rpm | |
| Aspiration | Turbochanged changed air cooler | |
| Torque Rise | 32% |
02 Operational Specification
| Operating Weight | 23926lb | 10853kg |
|---|---|---|
| Fuel Capacity | 65gal | 246L |
| Hydraulic System Fluid Capacity | 26gal | 97L |
| Engine Oil Fluid Capacity | 4.7gal | 17.5L |
| Cooling System Fluid Capacity | 5.1gal | 19L |
| Transmission Fluid Capacity | 4.9gal | 18.5L |
| Front Axle/Diff Fluid Capacity | 5.9gal | 22L |
| Rear Axle/Diff Fluid Capacity | 5.9gal | 22L |
| Turning Radius | 15.5ft in | 4700.1mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 80amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 17.5 R25 |
03 Transmission Specification
| Transmission Type | Countershaft type PowerShift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 23.4mph | 37.7km/h |
| Max Speed - Reverse | 15.7mph | 25.3km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3600psi | 24800kPa |
|---|---|---|
| Pump Flow Capacity | 37gal/min | 140L/min |
| Raise Time | 5.5sec | |
| Dump Time | 1.1sec | |
| Lower Time | 1.9sec | |
| Pump Type | Variable axial piston |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 8.75ft in | 2680mm |
|---|---|---|
| Breakout Force | 16233lb | 72.2kN |
| Bucket Capacity - Heaped | 2.5yd3 | 1.9m3 |
| Bucket Capacity - Struck | 2.1yd3 | 1.6m3 |
| Bucket Width | 8.33ft in | 2538.99mm |
06 Dimensions Dimensions
| Ground Clearance | 1.3ft in | 396mm |
|---|---|---|
| Length With Bucket On Ground | 22.75ft in | 6930mm |
| Wheelbase | 9ft in | 2750mm |
| Hinge Pin - Max Height | 12ft in | 3660mm |
| Reach At Max Lift And Dump | 3.67ft in | 1140mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.