Specification sheet Skid Steer Loader Ref john-deere-315-skid-steer-loader

John Deere 315

The John Deere 315 is a skid steer loader with an operating weight of 5,200 lb (2,358.69 kg), a 45 hp engine, a rated operating capacity of 1,501.35 lb (681 kg), and a tipping load of 3,000 lb (1,360.78 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
5,200lb
2,358.69kg
Engine power
45hp
33.56kW
Net Power
Rated operating capacity
1,501.35lb
681kg
Tipping load
3,000lb † — value reconstructed from related published figures
1,360.78kg
Bucket capacity
0.6yd³
0.5m³

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the John Deere 315 sits below the median for its class:

  • Operating weight 5,200 lb lighter than 85% (n=334)
  • Engine power 45 hp less powerful than 84% (n=335)
  • Rated operating capacity 1,500 lb lower-rated than 70% (n=288)

◇Scale drawingdrawn to scale · mm

1960C193D3270A2570B
Side elevation
1960C1500E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2240
Engine Model 4024T
Gross Power 49hp 36.6kw
Net Power 45hp 33.6kw
Power Measured @ 2400rpm
Aspiration Turbocharged
Displacement 149cu in 2.5L

02 Operational Specification

Operational Weight 5200lb 2358.7kg
Fuel Capacity 17.5gal 66L
Cooling System Fluid Capacity 1.7gal 6.2L
Engine Oil Fluid Capacity 2.4gal 9L
Max Speed 6.8mph 11km/h
Hydraulic System Fluid Capacity 5.1gal 19L
Chain Box Fluid Capacity - Each Side 4.4gal 16.3L
Tire Size 10x16.5 8 PR
Operating Voltage 12V
Alternator Supplied Amperage 70amps

03 Loader Specification

Breakout Force 3302.6lb 1498kg
Operating Load Rating 1501.4lb 681kg
Bucket Capacity 0.6yd3 0.5m3

04 Hydraulic Specification

Pump Flow Capacity 16.2gal/min 61L/min
Relief Valve Pressure 3450psi 23786.9kPa

05 Dimensions Dimensions

Length With Bucket 10.73ft in 3270mm
Width Over Tires 4.93ft in 1500mm
Ground Clearance 7.6in 193mm
Height To Top Of Cab 6.44ft in 1960mm
Wheelbase 3.42ft in 1040mm
Length W/O Bucket 8.44ft in 2570mm
Clearance At Max Lift And Dump 7.42ft in 2260mm
Reach At Max Lift And Dump 15.79in 401mm
Turning Radius From Center - Inc Bucket 75.99in 1930mm

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.