JCB 8010 CTS
The JCB 8010 CTS is a mini excavator with an operating weight of 2,447.2 lb, and a 18.6 hp engine.
✓ QA-verified — every figure checked for physical possibility and class plausibility; failures withheld →◆Where it sits in its classpercentile · mini excavators
Among 479 mini excavators , the JCB 8010 CTS sits at the compact end of its class:
- Operating weight 2,450 lb lighter than 95% (n=438)
- Engine power 19 hp less powerful than 71% (n=448)
Not positioned on dig depth — withheld or unpublished for this machine.
01 Boom/Stick Option (Hex) 1 Specification
| Max Reach Along Ground | 10.14ft in | 3,091mm‖ — metric converted from the published imperial value |
|---|---|---|
| Maximum Vertical Wallcut Depth | 5.3ft in | 1,615mm‖ — metric converted from the published imperial value |
| Max.Dumping Height | 5.88ft in | 1,792mm‖ — metric converted from the published imperial value |
| Maximum Digging Depth – Dozer Up | 6.29ft in | 1,917mm‖ — metric converted from the published imperial value |
| Max Digging Height | 8.54ft in | 2,603mm‖ — metric converted from the published imperial value |
02 Dimensions Specification
| Tail Swing Radius | 2.96ft in | 902mm‖ — metric converted from the published imperial value |
|---|---|---|
| Undercarriage Overall Length | 4.04ft in | 1,231mm‖ — metric converted from the published imperial value |
| Width Over Tracks | 2.3ft in | 701mm‖ — metric converted from the published imperial value |
| Overall Height | 7.53ft in | 2,295mm‖ — metric converted from the published imperial value |
| Overall Length | 9.71ft in | 2,960mm‖ — metric converted from the published imperial value |
03 Undercarriage Specification
| Number Of Track Rollers Per Side | 3 | |
|---|---|---|
| Drawbar Pull | 2023.29lb | 917.748kg‖ — metric converted from the published imperial value |
| Track Tension | Grease |
04 Engine Specification
| Starter Motor | 1.2KW | |
|---|---|---|
| Engine Model | 403D-11 | |
| Gross Power | 18.6hp | 13.9kw‖ — metric converted from the published imperial value |
| Cooling System | Water cooled | |
| Power Measured @ | 1800rpm | |
| Displacement | 69017.9cu in | 1,131,003cm3‖ — metric converted from the published imperial value |
| Alternator | 15amps |
05 Operational Specification
| Operating Weight | 2447.2lb | 1,110kg‖ — metric converted from the published imperial value |
|---|---|---|
| Fuel Capacity | 3.1gal | 12l‖ — metric converted from the published imperial value |
| Hydraulic System Fluid Capacity | 5.6gal | 21l‖ — metric converted from the published imperial value |
| Engine Oil Capacity | 0.8gal | 3l‖ — metric converted from the published imperial value |
| Water Spray System Fluid Capacity | 0.7gal | 3l‖ — metric converted from the published imperial value |
| Hydraulic Pump Flow Capacity | 4.3gal/min | 16l/min‖ — metric converted from the published imperial value |
06 Performance Specification
| Gradeability | 35% |
|---|
07 Hydraulic System Specification
| Nominal Output | 3.2gal/min | 12l/min‖ — metric converted from the published imperial value |
|---|---|---|
| Slew Main Relief | 95lpm | |
| Excavator/Track Main Relief | 180bar | |
| Auxiliary Hydraulic Flow | 6.4gal/min | 24l/min‖ — metric converted from the published imperial value |
| Pump Type | 3 section gear |
08 Boom Specification
| Boom Swing Left | 70degrees | |
|---|---|---|
| Boom Swing Right | 70degrees | |
| Bucket Rotation | 201degrees | |
| Bucket Tearout | 2090.8lb | 948.37kg‖ — metric converted from the published imperial value |
| Dipper Tearout | 1034.2lb | 469.1kg‖ — metric converted from the published imperial value |
Data notes
Converted metric figure. The source published imperial figures only for this machine. Metric figures marked ‖ are unit conversions of the published imperial value, rounded to the same precision — they are not separately published measurements. Because there is no independently published metric figure to compare against, no cross-unit consistency check applies to them; the imperial figures they derive from were checked for physically possible magnitude and for plausibility against this equipment class.
Method. Figures are manufacturer reference specifications, not measurements. The source published imperial figures for this machine in a single unit system, so no cross-unit consistency check applies; every value is checked for physically possible magnitude and for plausibility against its equipment class before publication. Figures that fail either check are withheld rather than shown, and figures reconstructed from related data are marked above. Metric figures marked ‖ are converted from the published imperial value rather than reproduced from the source.