Specification sheet Wheel Loader Ref jcb-435s-hl-wheel-loader
JCB 435S HL
The JCB 435S HL is a wheel loader with an operating weight of 31,448.94 lb (14,265 kg), a 206 hp engine, and a 2.49 yd³ (1.9 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
31,448.94lb
14,265kg
Engine power
206hp
153.7kW
Net Power Bucket capacity
2.49yd³
1.9m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the JCB 435S HL sits in the middle of its class:
- Operating weight 31,450 lb heavier than 54% (n=439)
- Engine power 206 hp more powerful than 82% (n=408)
- Bucket capacity 2.5 yd³ smaller-bucket than 85% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Emission Tier Level | EU Stage IV, US EPA Tier 4F | |
|---|---|---|
| Number Of Cylinders | 6 | |
| No. Of Valves | 4 | |
| Engine Model | QSB | |
| Engine Type | Cummins | |
| Net Power | 206hp | 153.7kw |
| Air Cleaner | Cyclonic pre-filter with engine fan scavenge system | |
| Gross Power | 230hp | 171.6kw |
| Power Measured @ | 2100rpm | |
| Max Torque | 945 Nm | |
| Displacement | 408.9cu in | 6.7L |
| Torque Measured @ | 1500rpm | |
| Aspiration | Turbo Charged | |
| Fan Drive Type | Hydraulically driven cooling fan |
02 Operational Specification
| Def Tank Capacity | 10.6gal | 40L |
|---|---|---|
| Auxiliary Fuel Tank | 105.7gal | 400L |
| Full Turn Tipping Load | 17357lb | 7873kg |
| Payload | 8679.6lb | 3937kg |
| Operating Weight | 31449lb | 14265kg |
| Fuel Capacity | 105.7gal | 400L |
| Hydraulic System Fluid Capacity | 55.5gal | 210L |
| Turning Radius | 19.8ft in | 6035mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 120amps | |
| Rear Axle Oscillation | 10.5degrees | |
| Articulation Angle | 40degrees |
03 Transmission Specification
| Transmission Type | 6 speed with lock up converter ZF 6WG210 | |
|---|---|---|
| Number Of Forward Gears | 6 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 32.5mph | 52.3km/h |
| Max Speed - Reverse | 22.5mph | 36.1km/h |
04 Hydraulic System Specification
| Max Operating Pressure | 250 bar | |
|---|---|---|
| Relief Valve Setting | 3190psi | 21994.3kPa |
| Pump Flow Capacity | 34.9gal/min | 132L/min |
| Raise Time | 4.7sec | |
| Dump Time | 1.8sec | |
| Lower Time | 2.8sec | |
| Total Cycle | 9.3sec | |
| Pump Type | Twin variable displacement piston pumps |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 11.14ft in | 3393mm |
|---|---|---|
| Bucket Capacity - Heaped | 2.49yd3 | 1.9m3 |
| Bucket Capacity - Struck | 2.12yd3 | 1.62m3 |
| Bucket Width | 8.36ft in | 2548mm |
| Breakout Force | 31023.64lb | 138kN |
06 Dimensions Dimensions
| Ground Clearance | 1.62ft in | 491mm |
|---|---|---|
| Length With Bucket On Ground | 24.69ft in | 7524mm |
| Width Over Tires | 9.72ft in | 2961mm |
| Height To Top Of Cab | 12.28ft in | 3742mm |
| Wheelbase | 10.01ft in | 3050mm |
| Hinge Pin - Max Height | 14.25ft in | 4342mm |
| Reach At Max Lift And Dump | 3.11ft in | 946mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.