Specification sheet Wheel Loader Ref jcb-427-ht-hl-wheel-loader
JCB 427 HT HL
The JCB 427 HT HL is a wheel loader with an operating weight of 29,938.78 lb (13,580 kg), a 146 hp engine, and a 2.36 yd³ (1.8 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
29,938.78lb
13,580kg
Engine power
146hp
108.9kW
Net Power Bucket capacity
2.36yd³
1.8m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the JCB 427 HT HL sits in the middle of its class:
- Operating weight 29,940 lb lighter than 55% (n=439)
- Engine power 146 hp less powerful than 68% (n=408)
- Bucket capacity 2.4 yd³ smaller-bucket than 88% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Emission Tier Level | EU Stage IV, US EPA Tier 4F | |
|---|---|---|
| Number Of Cylinders | 6 | |
| No. Of Valves | 4 | |
| Engine Model | QSB | |
| Engine Type | Cummins | |
| Net Power | 146hp | 108.9kw |
| Air Cleaner | Cyclonic pre filter with engine fan scavenge system | |
| Gross Power | 179hp | 133.5kw |
| Power Measured @ | 2100rpm | |
| Max Torque | 841 Nm | |
| Displacement | 408.9cu in | 6.7L |
| Torque Measured @ | 1500rpm | |
| Aspiration | Turbo Charged | |
| Fan Drive Type | Hydraulically driven cooling fan |
02 Operational Specification
| Def Tank Capacity | 10.6gal | 40L |
|---|---|---|
| Full Turn Tipping Load | 17610.6lb | 7988kg |
| Payload | 8805.3lb | 3994kg |
| Operating Weight | 29938.8lb | 13580kg |
| Fuel Capacity | 76.7gal | 290L |
| Hydraulic System Fluid Capacity | 55.5gal | 210L |
| Turning Radius | 19.8ft in | 6035mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 120amps | |
| Rear Axle Oscillation | 10.5degrees | |
| Articulation Angle | 40degrees |
03 Transmission Specification
| Transmission Type | 4 speed non-lock up converter 4WG | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24mph | 38.5km/h |
| Max Speed - Reverse | 15.4mph | 24.7km/h |
04 Hydraulic System Specification
| Max Operating Pressure | 250 bar | |
|---|---|---|
| Relief Valve Setting | 3190psi | 21994.3kPa |
| Pump Flow Capacity | 33.3gal/min | 126L/min |
| Raise Time | 5.1sec | 5.08sec |
| Dump Time | 1.5sec | 1.41sec |
| Lower Time | 3.3sec | |
| Total Cycle | 9.8sec | 9.79sec |
| Pump Type | Variable displacement |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 10.66ft in | 3247mm |
|---|---|---|
| Bucket Capacity - Heaped | 2.36yd3 | 1.8m3 |
| Bucket Capacity - Struck | 2.04yd3 | 1.56m3 |
| Bucket Width | 8.37ft in | 2550mm |
| Breakout Force | 31023.64lb | 138kN |
06 Dimensions Dimensions
| Ground Clearance | 1.55ft in | 472mm |
|---|---|---|
| Length With Bucket On Ground | 24.72ft in | 7532mm |
| Width Over Tires | 8.15ft in | 2483mm |
| Height To Top Of Cab | 11.03ft in | 3360mm |
| Wheelbase | 10.01ft in | 3050mm |
| Hinge Pin - Max Height | 14.13ft in | 4306mm |
| Reach At Max Lift And Dump | 3.89ft in | 1184mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.