Specification sheet Wheel Loader Ref jcb-419s-ht-wheel-loader
JCB 419S HT
The JCB 419S HT is a wheel loader with an operating weight of 23,397.66 lb (10,613 kg), a 183 hp engine, and a 2.1 yd³ (1.6 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
23,397.66lb
10,613kg
Engine power
183hp
136.5kW
Net Power Bucket capacity
2.1yd³
1.6m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the JCB 419S HT sits at the compact end of its class:
- Operating weight 23,400 lb lighter than 92% (n=439)
- Engine power 183 hp more powerful than 66% (n=408)
- Bucket capacity 2.1 yd³ smaller-bucket than 95% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Emission Tier Level | EU Stage IV, US EPA Tier 4F | |
|---|---|---|
| Number Of Cylinders | 6 | |
| No. Of Valves | 4 | |
| Engine Model | QSB | |
| Engine Type | Cummins | |
| Net Power | 183hp | 136.5kw |
| Air Cleaner | Cyclonic pre-filter with engine fan scavenge system | |
| Gross Power | 173hp | 129.1kw |
| Power Measured @ | 2100rpm | |
| Max Torque | 841 Nm | |
| Displacement | 408.9cu in | 6.7L |
| Torque Measured @ | 1500rpm | |
| Aspiration | Turbo Charged | |
| Fan Drive Type | Hydraulically driven cooling fan |
02 Operational Specification
| Def Tank Capacity | 6.3gal | 23.8L |
|---|---|---|
| Auxiliary Fuel Tank | 66.1gal | 250L |
| Full Turn Tipping Load | 15366.3lb | 6970kg |
| Payload | 7683.2lb | 3485kg |
| Operating Weight | 23397.7lb | 10613kg |
| Fuel Capacity | 66.1gal | 250L |
| Hydraulic System Fluid Capacity | 41gal | 155L |
| Turning Radius | 18.9ft in | 5740mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 120amps | |
| Rear Axle Oscillation | 9degrees | |
| Articulation Angle | 38degrees |
03 Transmission Specification
| Transmission Type | 6 speed non-lock up converter ZF | |
|---|---|---|
| Number Of Forward Gears | 6 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.9mph | 40km/h |
| Max Speed - Reverse | 20mph | 32.1km/h |
04 Hydraulic System Specification
| Max Operating Pressure | 230 bar | |
|---|---|---|
| Relief Valve Setting | 3190psi | 21994.3kPa |
| Pump Flow Capacity | 47.6gal/min | 180L/min |
| Raise Time | 3.9sec | 3.86sec |
| Dump Time | 1.6sec | 1.53sec |
| Lower Time | 2.4sec | |
| Total Cycle | 7.8sec | 7.79sec |
| Pump Type | Variable placement |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.03ft in | 2750mm |
|---|---|---|
| Bucket Capacity - Heaped | 2.1yd3 | 1.6m3 |
| Bucket Capacity - Struck | 1.78yd3 | 1.36m3 |
| Bucket Width | 7.88ft in | 2400mm |
| Breakout Force | 20682.43lb | 92kN |
06 Dimensions Dimensions
| Ground Clearance | 1.65ft in | 502mm |
|---|---|---|
| Length With Bucket On Ground | 21.75ft in | 6627mm |
| Width Over Tires | 8.78ft in | 2674mm |
| Height To Top Of Cab | 10.47ft in | 3191mm |
| Wheelbase | 9.36ft in | 2850mm |
| Hinge Pin - Max Height | 12.14ft in | 3700mm |
| Reach At Max Lift And Dump | 2.76ft in | 840mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.