JCB 300
The JCB 300 is a skid steer loader with an operating weight of 9,288.08 lb (4,213 kg), a 74 hp engine, a rated operating capacity of 3,000 lb (1,360.78 kg), and a tipping load of 6,369.2 lb (2,889.02 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the JCB 300 sits at the heavy end of its class:
- Operating weight 9,290 lb heavier than 95% (n=334)
- Engine power 74 hp more powerful than 69% (n=335)
- Rated operating capacity 3,000 lb higher-rated than 91% (n=288)
◇Scale drawingdrawn to scale · mm
01 Tyres Specification
| Standard | 12 x 16.5 - 10 PR Xtra Wall Off Road |
|---|
02 Engine Specification
| Emissions Certification | EPA-T4F (EU St3B) | |
|---|---|---|
| Fuel | Diesel | |
| Starter Motor | 4.2 KW | |
| Battery | 12 V | |
| Engine Oil Service Interval | 500 hours | |
| Engine Make | 2257 | |
| Engine Model | EcoMAX TCAE-55 | |
| Gross Power | 74hp | 55.2kw |
| Cooling System | Liquid | |
| Power Measured @ | 2400rpm | |
| Max Torque | 295.1lb ft | 400Nm |
| Torque Measured @ | 1200rpm | |
| Aspiration | Turbo | |
| Displacement | 268cu in | 4.4L |
03 Operational Specification
| Operational Weight | 9288.1lb | 4213kg |
|---|---|---|
| Fuel Capacity | 27.3gal | 103L |
| Cooling System Fluid Capacity | 4.1gal | 15.5L |
| Engine Oil Fluid Capacity | 4gal | 15L |
| Hydraulic System Fluid Capacity | 14.6gal | 55L |
| Max Speed | 12.4mph | 20km/h |
| Chain Box Fluid Capacity - Each Side | 6.1gal | 23L |
| Operating Speed | 6.8mph | 11km/h |
| Tire Size | 12 x 16.5 | |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 95amps |
04 Transmission Specification
| Model | Two Speed | |
|---|---|---|
| Travel Speed | 12.5mph | 20km/h |
05 Loader Specification
| Loader Lift Capacity With Bucket | 6056.1lb | 2747kg |
|---|---|---|
| Breakout Force | 6543.4lb | 2968kg |
| Operating Load Rating | 3000lb | 1360.8kg |
| Bucket Capacity | 0.6yd3 | 0.5m3 |
| Bucket Width | 74.9in | 1900mm |
06 Hydraulic Specification
| Pump Flow Capacity | 23.8gal/min | 90L/min |
|---|---|---|
| Relief Valve Pressure | 3335psi | 22994kPa |
07 Dimensions Dimensions
| Length With Bucket | 12.41ft in | 3780mm |
|---|---|---|
| Width Over Tires | 5.91ft in | 1800mm |
| Ground Clearance | 9.85in | 250mm |
| Height To Top Of Cab | 6.86ft in | 2090mm |
| Wheelbase | 4.11ft in | 1250mm |
| Clearance At Max Lift And Dump | 8.08ft in | 2460mm |
| Reach At Max Lift And Dump | 35.44in | 900mm |
| Turning Radius From Center - Inc Bucket | 86.62in | 2200mm |
| Turning Radius From Center - Machine Rear | 69.3in | 1760mm |
| Loadover Height | 9514.44ft in | 2900m |
| Dump Angle | 42degrees | |
| Dump Height | 7.55ft in | 2300mm |
| Angle Of Departure | 29degrees | |
| Pin Height | 10498.69ft in | 3200m |
| Rollback - Ground Level | 30degrees |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.