Specification sheet Skid Steer Loader Ref jcb-280-skid-steer-loader

JCB 280

The JCB 280 is a skid steer loader with an operating weight of 8,060 lb (3,655.96 kg), a 84 hp engine, a rated operating capacity of 2,800 lb (1,270.06 kg), and a tipping load of 5,608 lb (2,543.75 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
8,060lb
3,655.96kg
Engine power
84hp
62.7kW
Gross Power
Rated operating capacity
2,800lb
1,270.06kg
Tipping load
5,608lb † — value reconstructed from related published figures
2,543.75kg
Bucket capacity
0.7yd³
0.5m³

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the JCB 280 sits above the median for its class:

  • Operating weight 8,060 lb heavier than 81% (n=334)
  • Engine power 84 hp more powerful than 87% (n=335)
  • Rated operating capacity 2,800 lb higher-rated than 88% (n=288)

◇Scale drawingdrawn to scale · mm

2090B238C3760A
Side elevation
2090B1830D
Front elevation

01 Engine Specification

Engine Make 2257
Engine Model TC-63
Gross Power 84hp 62.7kw
Power Measured @ 2400rpm
Max Torque 267lb ft 362.1Nm
Torque Measured @ 1800rpm
Aspiration Turbocharged
Displacement 268cu in 4.4L

02 Operational Specification

Operational Weight 8060lb 3656kg
Fuel Capacity 27.3gal 103L
Cooling System Fluid Capacity 4.1gal 15.5L
Engine Oil Fluid Capacity 3.7gal 14L
Hydraulic System Fluid Capacity 15.9gal 60L
Max Speed 12.4mph 20km/h
Chain Box Fluid Capacity - Each Side 6.1gal 23L
Operating Speed 6.8mph 11km/h
Tire Size 12 x 16.5
Operating Voltage 12V
Alternator Supplied Amperage 95amps

03 Loader Specification

Operating Load Rating 2800lb 1270.1kg
Bucket Capacity 0.7yd3 0.5m3

04 Hydraulic Specification

Pump Flow Capacity 23gal/min 87.1L/min
Relief Valve Pressure 3335psi 22994kPa

05 Dimensions Dimensions

Length With Bucket 12.34ft in 3760mm
Width Over Tires 6.01ft in 1830mm
Ground Clearance 9.38in 238mm
Height To Top Of Cab 6.86ft in 2090mm
Wheelbase 4.01ft in 1220mm
Clearance At Max Lift And Dump 8.08ft in 2460mm
Reach At Max Lift And Dump 34.26in 870mm
Turning Radius From Center - Machine Rear 69.3in 1760mm
Turning Radius From Center - Inc Bucket 86.62in 2200mm

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.