Specification sheet Skid Steer Loader Ref jcb-250-skid-steer-loader
JCB 250
The JCB 250 is a skid steer loader with an operating weight of 8,214.43 lb (3,726 kg), a 73.8 hp engine, and a 0.6 yd³ (0.5 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
8,214.43lb
3,726kg
Engine power
73.8hp
55kW
Gross Power Bucket capacity
0.6yd³
0.5m³
◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the JCB 250 sits above the median for its class:
- Operating weight 8,210 lb heavier than 84% (n=334)
- Engine power 74 hp more powerful than 67% (n=335)
Not positioned on rated operating capacity — withheld or unpublished for this machine.
◇Scale drawingdrawn to scale · mm
01 Tyres Specification
| Standard | 12 x 16.5 - 10 PR Xtra Wall Off Road |
|---|
02 Engine Specification
| Emissions Certification | EPA-T4F (EU St3B) | |
|---|---|---|
| Fuel | Diesel | |
| Starter Motor | 4.2 KW | |
| Battery | 12 V | |
| Hydraulically Driven Cooling Fan | Yes | |
| Engine Oil Service Interval | 500 hours | |
| Engine Model | EcoMAX TCAE-55 | |
| Gross Power | 73.8hp | 55kw |
| Cooling System | Diesel | |
| Power Measured @ | 2400rpm | |
| Max Torque | 295.1lb ft | 400Nm |
| Torque Measured @ | 1200rpm | |
| Aspiration | Turbo | |
| Displacement | 4399cu in | 72.1L |
| Alternator | 95amps |
03 Capacities Specification
| Fuel Tank | 27.3gal | 103.3L |
|---|---|---|
| Hydraulic System | 14.6gal | 55L |
| Engine Oil | 4gal | 15L |
| Engine Coolant | 5.9gal | 22L |
04 Operational Specification
| Operational Weight | 8214.5lb | 3726kg |
|---|
05 Transmission Specification
| Model | Two Speed | |
|---|---|---|
| Travel Speed | 12mph | 19.4km/h |
06 Loader Specification
| Loader Lift Capacity With Bucket | 5884.2lb | 2669kg |
|---|---|---|
| Breakout Force | 6543.4lb | 2968kg |
| Bucket Capacity | 0.6yd3 | 0.5m3 |
| Bucket Width | 78.4in | 1990mm |
07 Hydraulic Specification
| Pump Flow Capacity | 23.8gal/min | 90L/min |
|---|---|---|
| Relief Valve Pressure | 483.8psi | 3335kPa |
08 Dimensions Dimensions
| Ground Clearance | 9.85in | 250mm |
|---|---|---|
| Wheelbase | 4.11ft in | 1250mm |
| Dump Angle | 42degrees | |
| Dump Height | 7.55ft in | 2300mm |
| Loadover Height | 9514.44ft in | 2900m |
| Max. Reach @ Full Height | 3.29ft in | 1m |
| Overall Height | 6.89ft in | 2100mm |
| Overall Length | 152.76in | 3880mm |
| Pin Height | 10.5ft in | 3.2m |
| Quick Hitch Turning Radius | 4.93ft in | 1.5m |
| Reach @ Ground Level | 3.61ft in | 1.11m |
| Rear Chassis Turning Radius | 5.78ft in | 1.76m |
| Rollback - Ground Level | 30degrees | |
| Angle Of Departure | 29degrees | |
| Width Over Tyres | 70.87in | 1800mm |
| Bucket Corner Turning Radius | 7.55ft in | 2.3m |
?Questions & answersfrom this machine's data
- How much does a JCB 250 skid steer weigh?
- A JCB 250 skid steer has an operating weight of 8,214.4 lb (3,726 kg).
- What engine does a JCB 250 skid steer have?
- A JCB 250 skid steer is powered by a EcoMAX TCAE-55 engine producing 73.8 hp (55 kW).
- What is the ground clearance of a JCB 250 skid steer?
- A JCB 250 skid steer has a ground clearance of 9.9 in (250 mm).
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.