JCB 190
The JCB 190 is a skid steer loader with an operating weight of 7,717 lb (3,500.38 kg), a 70 hp engine, a rated operating capacity of 1,985 lb (900.39 kg), and a tipping load of 3,969 lb (1,800.31 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the JCB 190 sits above the median for its class:
- Operating weight 7,720 lb heavier than 73% (n=334)
- Engine power 70 hp more powerful than 59% (n=335)
- Rated operating capacity 1,990 lb higher-rated than 53% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Model | 1104C-44 | |
| Gross Power | 80hp | 59.7kw |
| Net Power | 70hp | 52.2kw |
| Power Measured @ | 2200rpm | |
| Aspiration | Natural aspirated | |
| Displacement | 244.1cu in | 4L |
02 Operational Specification
| Operational Weight | 7717lb | 3500.4kg |
|---|---|---|
| Fuel Capacity | 28.2gal | 106.8L |
| Cooling System Fluid Capacity | 3.9gal | 14.8L |
| Engine Oil Fluid Capacity | 2.3gal | 8.6L |
| Hydraulic System Fluid Capacity | 9.2gal | 34.9L |
| Max Speed | 6.9mph | 11.2km/h |
| Chain Box Fluid Capacity - Each Side | 3.3gal | 12.5L |
| Tire Size | 12 x 16.5 - 10 pr | |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 72amps |
03 Loader Specification
| Breakout Force | 4387.2lb | 1990kg |
|---|---|---|
| Operating Load Rating | 1985lb | 900.4kg |
| Bucket Capacity | 0.7yd3 | 0.5m3 |
04 Hydraulic Specification
| Pump Type | Hydrostatic drive pumps | |
|---|---|---|
| Pump Flow Capacity | 20gal/min | 75.8L/min |
| Relief Valve Pressure | 2682psi | 18491.8kPa |
05 Dimensions Dimensions
| Length With Bucket | 11.49ft in | 3500mm |
|---|---|---|
| Width Over Tires | 5.55ft in | 1691mm |
| Height To Top Of Cab | 6.61ft in | 2014mm |
| Wheelbase | 3.7ft in | 1126mm |
| Length W/O Bucket | 8.19ft in | 2496mm |
| Clearance At Max Lift And Dump | 7.95ft in | 2423mm |
| Reach At Max Lift And Dump | 24.93in | 633mm |
| Turning Radius From Center - Machine Rear | 65.52in | 1664mm |
| Turning Radius From Center - Inc Bucket | 86.58in | 2199mm |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.