Specification sheet Skid Steer Loader Ref jcb-175-skid-steer-loader
JCB 175
The JCB 175 is a skid steer loader with an operating weight of 6,818.9 lb (3,093 kg), a 56 hp engine, and a 0.5 yd³ (0.4 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
6,818.9lb
3,093kg
Engine power
56hp
41.8kW
Gross Power Bucket capacity
0.5yd³
0.4m³
◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the JCB 175 sits in the middle of its class:
- Operating weight 6,820 lb heavier than 50% (n=334)
- Engine power 56 hp less powerful than 66% (n=335)
Not positioned on rated operating capacity — withheld or unpublished for this machine.
◇Scale drawingdrawn to scale · mm
01 Tyres Specification
| Standard | 10 x 16.5 - 8 PR Xtra Wall Off Road |
|---|
02 Engine Specification
| Emissions Certification | EPA-T4F (EU St3B) | |
|---|---|---|
| Fuel | Diesel | |
| Starter Motor | 2 KW | |
| Battery | 12 V | |
| Hydraulically Driven Cooling Fan | Yes | |
| Engine Oil Service Interval | 500 hours | |
| Engine Model | Kohler KDI 1903TCR/26B | |
| Gross Power | 56hp | 41.8kw |
| Cooling System | Diesel | |
| Power Measured @ | 2400rpm | |
| Max Torque | 166lb ft | 225Nm |
| Torque Measured @ | 1200rpm | |
| Aspiration | Turbo | |
| Displacement | 1860cu in | 30.5L |
| Alternator | 100amps |
03 Capacities Specification
| Fuel Tank - Diesel | 24.4gal | 92L |
|---|---|---|
| Hydraulic System | 11.5gal | 43.5L |
| Engine Oil | 2gal | 7.4L |
| Engine Coolant | 2.7gal | 10L |
04 Operational Specification
| Operational Weight | 6818.9lb | 3093kg |
|---|
05 Transmission Specification
| Model | Single Speed | |
|---|---|---|
| Travel Speed | 7.5mph | 12km/h |
06 Loader Specification
| Loader Lift Capacity With Bucket | 3461.3lb | 1570kg |
|---|---|---|
| Tipping Load - No Counterweight | 3505.4lb | 1590kg |
| Breakout Force | 4717.9lb | 2140kg |
| Bucket Capacity | 0.5yd3 | 0.4m3 |
| Bucket Width | 66.2in | 1680mm |
07 Hydraulic Specification
| Pump Flow Capacity | 18.5gal/min | 70L/min |
|---|---|---|
| Relief Valve Pressure | 3335psi | 22994kPa |
08 Dimensions Dimensions
| Ground Clearance | 8.27in | 210mm |
|---|---|---|
| Wheelbase | 3.52ft in | 1070mm |
| Dump Angle | 42degrees | |
| Dump Height | 7.42ft in | 2260mm |
| Loadover Height | 9317.59ft in | 2840m |
| Max. Reach @ Full Height | 3.97ft in | 1.21m |
| Overall Height | 6.5ft in | 1980mm |
| Overall Length | 137.41in | 3490mm |
| Pin Height | 9.91ft in | 3.02m |
| Quick Hitch Turning Radius | 3.75ft in | 1.14m |
| Reach @ Ground Level | 3.55ft in | 1.08m |
| Rear Chassis Turning Radius | 5.42ft in | 1.65m |
| Rollback - Ground Level | 30degrees | |
| Angle Of Departure | 25degrees | |
| Width Over Tyres | 59.85in | 1520mm |
| Bucket Corner Turning Radius | 6.86ft in | 2.09m |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.