JCB 170
The JCB 170 is a skid steer loader with an operating weight of 5,534 lb (2,510.19 kg), a 47 hp engine, a rated operating capacity of 1,543 lb (699.9 kg), and a tipping load of 3,086 lb (1,399.79 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the JCB 170 sits below the median for its class:
- Operating weight 5,530 lb lighter than 77% (n=334)
- Engine power 47 hp less powerful than 78% (n=335)
- Rated operating capacity 1,540 lb lower-rated than 69% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Model | 404C-22 | |
| Gross Power | 50hp | 37.3kw |
| Net Power | 47hp | 35.1kw |
| Power Measured @ | 2800rpm | |
| Aspiration | Naturally aspirated | |
| Displacement | 134.3cu in | 2.2L |
02 Operational Specification
| Operational Weight | 5534lb | 2510.2kg |
|---|---|---|
| Fuel Capacity | 21gal | 79.5L |
| Cooling System Fluid Capacity | 2.1gal | 8L |
| Engine Oil Fluid Capacity | 2.5gal | 9.5L |
| Hydraulic System Fluid Capacity | 7.9gal | 30L |
| Max Speed | 6.9mph | 11.2km/h |
| Chain Box Fluid Capacity - Each Side | 4.5gal | 17.1L |
| Tire Size | 10 x 16.5 - 6 pr Wide Track | |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 55amps |
03 Loader Specification
| Breakout Force | 3197lb | 1450.2kg |
|---|---|---|
| Operating Load Rating | 1543lb | 699.9kg |
| Bucket Capacity | 0.5yd3 | 0.4m3 |
04 Hydraulic Specification
| Pump Type | Hydrostatic drive pumps | |
|---|---|---|
| Pump Flow Capacity | 15.9gal/min | 60.2L/min |
| Relief Valve Pressure | 2683psi | 18498.7kPa |
05 Dimensions Dimensions
| Length With Bucket | 10.73ft in | 3270mm |
|---|---|---|
| Width Over Tires | 5.25ft in | 1600mm |
| Height To Top Of Cab | 6.37ft in | 1940mm |
| Wheelbase | 3.38ft in | 1030mm |
| Length W/O Bucket | 7.91ft in | 2410mm |
| Clearance At Max Lift And Dump | 7.52ft in | 2290mm |
| Reach At Max Lift And Dump | 18.51in | 470mm |
| Turning Radius From Center - Machine Rear | 63.78in | 1620mm |
| Turning Radius From Center - Inc Bucket | 77.56in | 1970mm |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.