Specification sheet Skid Steer Loader Ref jcb-160-skid-steer-loader

JCB 160

The JCB 160 is a skid steer loader with an operating weight of 5,310 lb (2,408.58 kg), a 44 hp engine, a rated operating capacity of 1,322.78 lb (600 kg), and a tipping load of 2,645.6 lb (1,200.03 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
5,310lb
2,408.58kg
Engine power
44hp
32.82kW
Net Power
Rated operating capacity
1,322.78lb
600kg
Tipping load
2,645.6lb † — value reconstructed from related published figures
1,200.03kg
Bucket capacity
0.4yd³
0.3m³

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the JCB 160 sits below the median for its class:

  • Operating weight 5,310 lb lighter than 83% (n=334)
  • Engine power 44 hp less powerful than 85% (n=335)
  • Rated operating capacity 1,320 lb lower-rated than 85% (n=288)

◇Scale drawingdrawn to scale · mm

1930C3210A2340B
Side elevation
1930C1370D
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Model 404C-22
Gross Power 47hp 35.1kw
Net Power 44hp 32.9kw
Power Measured @ 2600rpm
Aspiration Naturally aspirated
Displacement 134.3cu in 2.2L

02 Operational Specification

Operational Weight 5310lb 2408.6kg
Fuel Capacity 21gal 79.5L
Cooling System Fluid Capacity 2.1gal 8L
Engine Oil Fluid Capacity 2.5gal 9.5L
Hydraulic System Fluid Capacity 7.9gal 30L
Max Speed 6.3mph 10.2km/h
Chain Box Fluid Capacity - Each Side 4.5gal 17.1L
Tire Size 7.00 x 15 - 6 pr
Operating Voltage 12V
Alternator Supplied Amperage 55amps

03 Loader Specification

Breakout Force 2998lb 1359.9kg
Operating Load Rating 1322.8lb 600kg
Bucket Capacity 0.4yd3 0.3m3

04 Hydraulic Specification

Pump Type Hydrostatic drive pumps
Pump Flow Capacity 14.5gal/min 54.9L/min
Relief Valve Pressure 2683psi 18498.7kPa

05 Dimensions Dimensions

Length With Bucket 10.54ft in 3210mm
Width Over Tires 4.5ft in 1370mm
Height To Top Of Cab 6.34ft in 1930mm
Wheelbase 3.22ft in 980mm
Length W/O Bucket 7.68ft in 2340mm
Clearance At Max Lift And Dump 7.09ft in 2160mm
Reach At Max Lift And Dump 22.45in 570mm
Turning Radius From Center - Machine Rear 62.21in 1580mm
Turning Radius From Center - Inc Bucket 73.63in 1870mm

?Questions & answersfrom this machine's data

How much does a JCB 160 skid steer weigh?
A JCB 160 skid steer has an operating weight of 5,310 lb (2,408.6 kg).
How much can a JCB 160 skid steer lift?
A JCB 160 skid steer has a rated operating capacity of 1,322.8 lb (600 kg).
What engine does a JCB 160 skid steer have?
A JCB 160 skid steer is powered by a 404C-22 engine producing 44 hp (32.8 kW).
How long is a JCB 160 skid steer?
A JCB 160 skid steer has an overall length of 10.5 ft (3,210 mm) with the bucket on the ground.

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.