Gehl CTL80
The Gehl CTL80 is a compact track loader with an operating weight of 10,692 lb (4,849.81 kg), a 97 hp engine, a rated operating capacity of 3,528 lb (1,600.28 kg), and a tipping load of 7,056 lb (3,200.55 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · compact track loaders
Among 184 compact track loaders , the Gehl CTL80 sits above the median for its class:
- Operating weight 10,690 lb heavier than 81% (n=182)
- Engine power 97 hp more powerful than 93% (n=167)
- Rated operating capacity 3,530 lb higher-rated than 80% (n=156)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2348 | |
| Engine Model | 4TNV106T | |
| Net Power | 97hp | 72.4kw |
| Power Measured @ | 2200rpm | |
| Peak Torque | 191lb ft | 259Nm |
| Torque Measured @ | 1400rpm | |
| Displacement | 269cu in | 4.5L |
| Aspiration | turbocharged |
02 Operational Specification
| Operating Weight | 10692lb | 4849.9kg |
|---|---|---|
| Cooling System Fluid Capacity | 4gal | 15.1L |
| Fuel Capacity | 28.6gal | 107.9L |
| Engine Oil Capacity | 3.7gal | 14L |
| Hydraulic System Fluid Capacity | 17gal | 64L |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 50amps | |
| Max Speed - Low Range | 5mph | 8km/h |
| Max Speed - High Range | 6.9mph | 11km/h |
03 Loader Specification
| Breakout Force | 8692lb | 3942.7kg |
|---|---|---|
| Operating Load | 3528lb | 1600.3kg |
04 Hydraulic Specification
| Pump Flow | 23.4gal/min | 88.6L/min |
|---|---|---|
| Relief Valve Pressure | 2988psi | 20601.6kPa |
05 Dimensions Dimensions
| Width Over Tracks | 6.19ft in | 1884mm |
|---|---|---|
| Height To Top Of Cab | 7.28ft in | 2217mm |
| Ground Clearance | 14.3in | 363mm |
| Clearance At Max Lift And Dump | 7.8ft in | 2375mm |
| Reach At Max Lift And Dump | 3.45ft in | 1049mm |
| Turning Radius From Center - Inc Bucket | 105.99in | 2692mm |
| Length With Bucket | 13.21ft in | 4026mm |
| Length With Out Bucket | 10.2ft in | 3106mm |
| Turning Radius From Center - Machine Rear | 71.5in | 1816mm |
06 Undercarriage Dimensions
| Length Of Track On Ground | 5.25ft in | 1598mm |
|---|---|---|
| Number Of Track Rollers Per Side | 5 | |
| Width Of Track | 18in | 457mm |
| Ground Pressure | 4.3psi | 29.65kPa |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.