Gehl CTL75
The Gehl CTL75 is a compact track loader with an operating weight of 9,700.34 lb (4,400 kg), a 83 hp engine, a rated operating capacity of 2,976.25 lb (1,350 kg), and a tipping load of 5,952.5 lb (2,700.01 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · compact track loaders
Among 184 compact track loaders , the Gehl CTL75 sits in the middle of its class:
- Operating weight 9,700 lb heavier than 58% (n=182)
- Engine power 83 hp more powerful than 72% (n=167)
- Rated operating capacity 2,980 lb higher-rated than 62% (n=156)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2348 | |
| Engine Model | 4TNV98T | |
| Gross Power | 83hp | 61.9kw |
| Power Measured @ | 2500rpm | |
| Peak Torque | 219lb ft | 297Nm |
| Torque Measured @ | 1800rpm | |
| Displacement | 202.5cu in | 3.4L |
| Aspiration | Turbocharged |
02 Operational Specification
| Operating Weight | 9700.4lb | 4400kg |
|---|---|---|
| Cooling System Fluid Capacity | 4.4gal | 16.5L |
| Fuel Capacity | 23.9gal | 90.1L |
| Engine Oil Capacity | 2.7gal | 10.2L |
| Hydraulic System Fluid Capacity | 12.9gal | 48.5L |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 40amps | |
| Max Speed - Low Range | 4.7mph | 7.6km/h |
| Max Speed - High Range | 7.2mph | 11.6km/h |
03 Loader Specification
| Operating Load | 2976.3lb | 1350kg |
|---|---|---|
| Bucket Capacity | 0.7yd3 | 0.5m3 |
04 Hydraulic Specification
| Pump Flow | 19.8gal/min | 74.9L/min |
|---|---|---|
| Relief Valve Pressure | 2988psi | 20601.6kPa |
05 Dimensions Dimensions
| Width Over Tracks | 5.81ft in | 1770mm |
|---|---|---|
| Height To Top Of Cab | 7.11ft in | 2167mm |
| Ground Clearance | 12.8in | 325mm |
| Clearance At Max Lift And Dump | 7.9ft in | 2405mm |
| Reach At Max Lift And Dump | 2.87ft in | 874mm |
| Turning Radius From Center - Inc Bucket | 90.32in | 2294mm |
| Length With Bucket | 12.28ft in | 3740mm |
| Length With Out Bucket | 9.78ft in | 2980mm |
| Turning Radius From Center - Machine Rear | 65.6in | 1666mm |
06 Undercarriage Dimensions
| Length Of Track On Ground | 4.91ft in | 1496mm |
|---|---|---|
| Number Of Track Rollers Per Side | 4 | |
| Width Of Track | 18in | 457mm |
| Ground Pressure | 4.3psi | 29.65kPa |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.