Gehl CTL65
The Gehl CTL65 is a compact track loader with an operating weight of 8,013.81 lb (3,635 kg), a 67 hp engine, a rated operating capacity of 2,314.86 lb (1,050 kg), and a tipping load of 4,629.8 lb (2,100.04 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · compact track loaders
Among 184 compact track loaders , the Gehl CTL65 sits below the median for its class:
- Operating weight 8,010 lb lighter than 70% (n=182)
- Engine power 67 hp less powerful than 70% (n=167)
- Rated operating capacity 2,310 lb lower-rated than 62% (n=156)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2348 | |
| Engine Model | 4TNV98 | |
| Gross Power | 67hp | 50kw |
| Power Measured @ | 2500rpm | |
| Peak Torque | 179lb ft | 242.7Nm |
| Torque Measured @ | 1600rpm | |
| Displacement | 202.5cu in | 3.4L |
| Aspiration | Natural |
02 Operational Specification
| Operating Weight | 8013.9lb | 3635kg |
|---|---|---|
| Cooling System Fluid Capacity | 4.4gal | 16.5L |
| Fuel Capacity | 19.9gal | 75L |
| Engine Oil Capacity | 2.7gal | 10.2L |
| Hydraulic System Fluid Capacity | 10.2gal | 38.6L |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 40amps | |
| Max Speed - Low Range | 4.5mph | 7.3km/h |
| Max Speed - High Range | 6.8mph | 11km/h |
03 Loader Specification
| Operating Load | 2314.9lb | 1050kg |
|---|---|---|
| Bucket Capacity | 0.6yd3 | 0.5m3 |
04 Hydraulic Specification
| Pump Flow | 18.4gal/min | 69.5L/min |
|---|---|---|
| Relief Valve Pressure | 2988psi | 20601.6kPa |
05 Dimensions Dimensions
| Width Over Tracks | 5.19ft in | 1580mm |
|---|---|---|
| Height To Top Of Cab | 6.97ft in | 2123mm |
| Ground Clearance | 12.21in | 310mm |
| Clearance At Max Lift And Dump | 7.78ft in | 2370mm |
| Reach At Max Lift And Dump | 2.4ft in | 730mm |
| Turning Radius From Center - Inc Bucket | 93in | 2362mm |
| Length With Bucket | 11.63ft in | 3543mm |
| Length With Out Bucket | 9.05ft in | 2756mm |
| Turning Radius From Center - Machine Rear | 60.99in | 1549mm |
06 Undercarriage Dimensions
| Length Of Track On Ground | 1389ft in | 423367.2mm |
|---|---|---|
| Number Of Track Rollers Per Side | 4 | |
| Width Of Track | 320in | 8128mm |
| Ground Pressure | 4.87psi | 33.51kPa |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.