Specification sheet Wheel Loader Ref clark-michigan-175c-wheel-loader
Clark Michigan 175C
The Clark Michigan 175C is a wheel loader with an operating weight of 57,780.96 lb (26,209 kg), a 288.4 hp engine, and a 5.5 yd³ (4.2 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
57,780.96lb
26,209kg
Engine power
288.4hp
215kW
Net Power Bucket capacity
5.5yd³
4.2m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Clark Michigan 175C sits above the median for its class:
- Operating weight 57,780 lb heavier than 64% (n=198)
- Engine power 288 hp more powerful than 59% (n=190)
- Bucket capacity 5.5 yd³ smaller-bucket than 56% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | NT-855C | |
| Net Power | 288.4hp | 215kw |
| Gross Power | 309.8hp | 231kw |
| Power Measured @ | 2100rpm | |
| Max Torque | 1006.1lb ft | 1364Nm |
| Displacement | 854.4cu in | 14L |
| Torque Measured @ | 1500rpm |
02 Operational Specification
| Operating Weight | 57781lb | 26209kg |
|---|---|---|
| Fuel Capacity | 124.1gal | 469.4L |
| Hydraulic System Fluid Capacity | 103.1gal | 389.9L |
| Engine Oil Fluid Capacity | 9.1gal | 34.1L |
| Cooling System Fluid Capacity | 20gal | 75.7L |
| Transmission Fluid Capacity | 12.5gal | 47.3L |
| Front Axle/Diff Fluid Capacity | 9.1gal | 34.1L |
| Rear Axle/Diff Fluid Capacity | 9.1gal | 34.1L |
| Static Tipping Weight | 48567.9lb | 22030kg |
| Turning Radius | 24.7ft in | 7525mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 75amps | |
| Rear Axle Oscillation | 23degrees | |
| Tire Size | 26.5-25 20PR |
03 Transmission Specification
| Transmission Type | Clark countershaft type powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 20.4mph | 32.8km/h |
| Max Speed - Reverse | 20.4mph | 32.8km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 2600psi | 17926.4kPa |
|---|---|---|
| Pump Flow Capacity | 118.1gal/min | 446.7L/min |
| Raise Time | 6.7sec | |
| Dump Time | 2sec | |
| Lower Time | 4.2sec | |
| Pump Type | tandem gear type |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 10.14ft in | 3089mm |
|---|---|---|
| Bucket Capacity - Heaped | 5.5yd3 | 4.2m3 |
| Bucket Capacity - Struck | 4.71yd3 | 3.6m3 |
| Bucket Width | 10.34ft in | 3150mm |
| Breakout Force | 38240lb | 170.1kN |
06 Dimensions Dimensions
| Ground Clearance | 1.76ft in | 536mm |
|---|---|---|
| Length With Bucket On Ground | 28.58ft in | 8710mm |
| Width Over Tires | 10.02ft in | 3053mm |
| Height To Top Of Cab | 12.16ft in | 3706mm |
| Wheelbase | 11.25ft in | 3429mm |
| Hinge Pin - Max Height | 14.04ft in | 4277mm |
| Reach At Max Lift And Dump | 4.29ft in | 1306mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.