Specification sheet Wheel Loader Ref clark-michigan-125c-wheel-loader
Clark Michigan 125C
The Clark Michigan 125C is a wheel loader with an operating weight of 43,475.17 lb (19,720 kg), a 214.6 hp engine, and a 4.45 yd³ (3.4 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
43,475.17lb
19,720kg
Engine power
214.6hp
160kW
Net Power Bucket capacity
4.45yd³
3.4m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Clark Michigan 125C sits at the heavy end of its class:
- Operating weight 43,480 lb heavier than 96% (n=439)
- Engine power 215 hp more powerful than 86% (n=408)
- Bucket capacity 4.5 yd³ larger-bucket than 90% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | LT-10-225 HT | |
| Net Power | 214.6hp | 160kw |
| Gross Power | 226.7hp | 169kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 750.2lb ft | 1017Nm |
| Displacement | 611cu in | 10.1L |
| Torque Measured @ | 1300rpm |
02 Operational Specification
| Operating Weight | 43475.2lb | 19720kg |
|---|---|---|
| Fuel Capacity | 75.1gal | 284L |
| Hydraulic System Fluid Capacity | 76.1gal | 288L |
| Engine Oil Fluid Capacity | 9gal | 34L |
| Cooling System Fluid Capacity | 15.1gal | 57L |
| Transmission Fluid Capacity | 10.6gal | 40L |
| Front Axle/Diff Fluid Capacity | 9.1gal | 34.1L |
| Rear Axle/Diff Fluid Capacity | 9.1gal | 34.1L |
| Static Tipping Weight | 32319.8lb | 14660kg |
| Turning Radius | 24.6ft in | 7475mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 100amps | |
| Rear Axle Oscillation | 18.5degrees | |
| Tire Size | 23.5-25 |
03 Transmission Specification
| Transmission Type | Clark countershaft powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 19.3mph | 30.9km/h |
| Max Speed - Reverse | 19.3mph | 30.9km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 2755.8psi | 19000kPa |
|---|---|---|
| Pump Flow Capacity | 90.5gal/min | 342.5L/min |
| Raise Time | 7.4sec | |
| Dump Time | 1.4sec | |
| Lower Time | 3.2sec | |
| Pump Type | tandem gear type |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.62ft in | 2930mm |
|---|---|---|
| Bucket Capacity - Heaped | 4.45yd3 | 3.4m3 |
| Bucket Capacity - Struck | 3.8yd3 | 2.9m3 |
| Bucket Width | 10ft in | 3048mm |
| Breakout Force | 39265.13lb | 174.66kN |
06 Dimensions Dimensions
| Ground Clearance | 1.19ft in | 360mm |
|---|---|---|
| Length With Bucket On Ground | 27.37ft in | 8340mm |
| Width Over Tires | 9.32ft in | 2840mm |
| Height To Top Of Cab | 11.29ft in | 3440mm |
| Wheelbase | 10.67ft in | 3251mm |
| Hinge Pin - Max Height | 13.34ft in | 4065mm |
| Reach At Max Lift And Dump | 3.55ft in | 1080mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.