Specification sheet Wheel Loader Ref caterpillar-962g-series-ii-wheel-loader
Caterpillar 962G Series II
The Caterpillar 962G Series II is a wheel loader with an operating weight of 40,889 lb (18,546.94 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
40,889lb
18,546.94kg
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Caterpillar 962G Series II sits at the heavy end of its class:
- Operating weight 40,890 lb heavier than 88% (n=439)
Not positioned on engine power, bucket capacity — withheld or unpublished for this machine.
01 Engine Specification
| Displacement | 439cu in | 7.2L |
|---|---|---|
| Bore | 4.3in | 109.3mm |
| Stroke | 5in | 127mm |
| Engine Model | Caterpillar 3126B with ATAAC | |
| Flywheel Power | 204hp | 152.2kw |
| Maximum Flywheel Power | 210hp | 156.6kw |
| Total Torque Rise | 38 % | |
| Peak Torque - 1,400 Rpm - Net | 669lb ft | 907.1Nm |
02 Operational Specification
| Operating Weight | 40889lb | 18547kg |
|---|
03 Transmission Specification
| Forward - 1 | 4.3mph | 7km/h |
|---|---|---|
| Forward - 2 | 7.9mph | 12.8km/h |
| Forward - 3 | 13.9mph | 22.4km/h |
| Forward - 4 | 23mph | 37.1km/h |
| Reverse - 1 | 4.7mph | 7.6km/h |
| Reverse - 2 | 8.6mph | 13.9km/h |
| Reverse - 3 | 15.2mph | 24.5km/h |
| Reverse - 4 | 24.9mph | 40.1km/h |
04 Weights Specification
| Operating Weight | 40889lb | 18547kg |
|---|
05 Tires Specification
| Tires | Choose from a variety of tires to match your application. |
|---|
06 Buckets Specification
| Maximum Bucket Capacity | 5yd3 | 3.9m3 |
|---|---|---|
| Bucket Capacities | 2.9-3.8 m3 3.75-5.0 yd3 |
07 Axles Specification
| Front | Fixed front | |
|---|---|---|
| Rear | Ocillating +/-13? | |
| Maximum Single-Wheel Rise And Fall | 18.5in | 469.9mm |
08 Hydraulic System Specification
| Hydraulic Cycle Time - Total | 11.4 s | |
|---|---|---|
| Hydraulic Cycle Time - Lower, Empty, Float Down | 3 s | |
| Hydraulic Cycle Time - Raise | 6.3 s | |
| Pilot System - Pump Output | 8.9 gal/min | |
| Bucket/Work Tool System - Relief Valve Setting | 3000 psi | |
| Pilot System - Main Valve Setting - Steering Wheel | 375 psi | |
| Pilot System - Main Valve Setting - Command Control System | 500 psi | |
| Hydraulic Cycle Time - Dump | 2.1 s |
09 Brakes Specification
| Brakes | Meets required standards. |
|---|
10 Operating Specifications Specification
| Static Tipping Load - Full Turn | 26380lb | 11965.8kg |
|---|---|---|
| Breakout Force | 31024lb | 14072.3kg |
11 Service Refill Capacities Specification
| Cooling System | 14.5gal | 54.9L |
|---|---|---|
| Crankcase | 8gal | 30.3L |
| Hydraulic Tank | 23gal | 87.1L |
| Hydraulic System - Including Tank | 40gal | 151.5L |
| Fuel Tank - Standard | 75.3gal | 285.1L |
| Transmission | 9gal | 34.1L |
| Differential - Final Drives - Front | 9.5gal | 36L |
| Differential - Final Drives - Rear | 9.5gal | 36L |
12 Cab Specification
| Rops/Fops | Meets SAE and ISO standards. |
|---|
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.