Specification sheet Wheel Loader Ref caterpillar-928hz-wheel-loader
Caterpillar 928Hz
The Caterpillar 928Hz is a wheel loader with an operating weight of 27,699 lb (12,564.06 kg), and a dig depth of 0.28 ft (86.11 mm).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
27,699lb
12,564.06kg
Dig depth
0.28ft
86.11mm
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Caterpillar 928Hz sits below the median for its class:
- Operating weight 27,700 lb lighter than 69% (n=439)
Not positioned on engine power, bucket capacity — withheld or unpublished for this machine.
01 Engine Specification
| Displacement | 403cu in | 6.7L |
|---|---|---|
| Net Torque | 536lb ft | 726.8Nm |
| Peak Torque | 547lb ft | 741.7Nm |
| Bore | 4.2in | 105mm |
| Stroke | 5in | 127mm |
| Rated Net Power | 149hp | 111.2kw |
| Sae J1349 (2) | 160hp | 119.4kw |
| Iso 9249 (1997) (2) | 161hp | 120.1kw |
| Eec 80/1269 (2) | 161hp | 120.1kw |
| Sae J1349 (1) | 149hp | 111.2kw |
| Iso 9249 (1997) (1) | 150hp | 111.9kw |
| Eec 80/1269 (1) | 150hp | 111.9kw |
| Maximum Net Power - 2000 Rpm | 160hp | 119.4kw |
02 Operational Specification
| Operating Weight | 27699lb | 12564.1kg |
|---|
03 Transmission Specification
| Forward - 1 | 4.9mph | 7.9km/h |
|---|---|---|
| Reverse - 1 | 4.9mph | 7.9km/h |
04 Steering Specification
| Steering Angle - Each Direction | 40degrees | |
|---|---|---|
| Minimum Turning Radius - Over Tires | 206in | 5232.4mm |
| Steering Cylinder, Two, Bore | 2.8in | 69.9mm |
| Hydraulic Output At 2300 Engine Rpm And 6900 Kpa (1000 Psi) | 27 gal/min | |
| Maximum Working Pressure | 3000 psi | |
| Steering Articulation | 40degrees |
05 Transmission Specification
| 2 | 7.8mph | 12.6km/h |
|---|---|---|
| 3 | 16mph | 25.8km/h |
| 4 | 23.4mph | 37.7km/h |
| Standard Transmission Maximum Travel Speeds | 23.4mph | 37.7km/h |
06 Tires Specification
| Tread Width | 8.5ft in | 2.6m |
|---|---|---|
| Size | 20.5 R25 L3 XHA |
07 Buckets Specification
| Bucket Capacities | 2.0 m3 - 2.3 m3 2.6 yd3 - 3.0 yd3 |
|---|
08 Operating Specifications Specification
| Static Tipping Load - Full Turn | 19089lb | 8658.7kg |
|---|---|---|
| Articulation Angle | 40degrees | |
| Reach - Full Lift And 45 Degrees Dump | 3ft in | 1m |
| Dump Clearance At Full Lift And 45 Degrees Dump Angle | 9.5ft in | 2.9m |
09 Service Refill Capacities Specification
| Cooling System | 11.1gal | 42.1L |
|---|---|---|
| Fuel Tank | 59.4gal | 224.9L |
| Crankcase | 4gal | 15.2L |
| Hydraulic Tank | 18.5gal | 70.1L |
| Hydraulic System - Including Tank | 33gal | 125L |
| Transmission | 9.1gal | 34.5L |
| Front | 6.9gal | 26.2L |
| Rear | 6.6gal | 25L |
10 Cab Specification
| Rops | SAE J1040 MAY94, ISO 3471-1994 | |
|---|---|---|
| Fops | SAE J/ISO 3449 APR98 Level II, ISO 3449-1992 Level II |
11 Loader Hydraulic System Specification
| Pump Flow - Implement Pump | 40.2 gal/min | |
|---|---|---|
| Output At 2,300 Engine Rpm And 6900 Kpa (1000 Psi) With Sae 10w Oil At 65 Degreesc (150 Degreesf) | 40.3 gal/min | |
| Maximum Working Pressure | 3755 psi | |
| Raise | 6.1 s | |
| Dump | 1.2 s | |
| Lower, Empty, Float Down | 2.8 s | |
| Total | 10.1 s | |
| Bore (1) | 4.8in | 120.7mm |
| Stroke (1) | 27in | 685.8mm |
| Bore (2) | 5in | 127mm |
| Stroke (2) | 21.7in | 551.2mm |
| Hydraulic Cycle Time | 10.1 Seconds | |
| Relief Pressure - Implement Pump | 3755 psi |
12 Dimensions Dimensions
| Ground Clearance | 1.34ft in | 408.44mm |
|---|---|---|
| Bucket Pin Height - Maximum Lift | 12.7ft in | 3.88m |
| Carry Height | 1.47ft in | 0.45m |
| Centerline Of Front Axle To Hitch | 4.76ft in | 1.46m |
| Digging Depth | 3.39in | 86.11mm |
| Dump Angle At Maximum Lift | 45degrees | |
| Dump Clearance At Maximum Lift - 45 Degrees | 9.45ft in | 2.89m |
| Height - Center Of Axle | 2.25ft in | 0.69m |
| Height - Top Of Exhaust Stack | 10.46ft in | 3.19m |
| Height - Top Of Hood | 86.52in | 2197.61mm |
| Height - Top Of Rops/Fops | 10.73ft in | 3.28m |
| Length - Rear Axle To Bumper | 6.3ft in | 1.93m |
| Overall Height - Bucket Raised | 16.31ft in | 4.98m |
| Overall Length | 23.79ft in | 7251.2mm |
| Rack Back Angle - Carry | 47.8degrees | |
| Rack Back Angle - Ground | 44degrees | |
| Rack Back Angle - Maximum Lift | 60degrees | |
| Reach At Maximum Lift And 45 Degrees Dump | 3.04ft in | 0.93m |
| Wheel Base | 9.51ft in | 2.9m |
| Bucket Clearance-Maximum Lift/Carry | 12.31ft in | 3.76m |
| Width - Over Tires | 8.43ft in | 2.57m |
?Questions & answersfrom this machine's data
- How much does a Caterpillar 928Hz wheel loader weigh?
- A Caterpillar 928Hz wheel loader has an operating weight of 27,699 lb (12,564.1 kg).
- What is the ground clearance of a Caterpillar 928Hz wheel loader?
- A Caterpillar 928Hz wheel loader has a ground clearance of 1.3 ft (408.4 mm).
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.