Specification sheet Wheel Loader Ref caterpillar-924k-wheel-loader
Caterpillar 924K
The Caterpillar 924K is a wheel loader with an operating weight of 28,360 lb (12,863.89 kg), and a dig depth of 0.32 ft (96.52 mm).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
28,360lb
12,863.89kg
Dig depth
0.32ft
96.52mm
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Caterpillar 924K sits below the median for its class:
- Operating weight 28,360 lb lighter than 63% (n=439)
Not positioned on engine power, bucket capacity — withheld or unpublished for this machine.
01 Engine Specification
| Displacement | 402cu in | 6.6L |
|---|---|---|
| Net Torque | 515lb ft | 698.3Nm |
| Bore | 4in | 101.6mm |
| Stroke | 5in | 127mm |
| Eec 80/1269 | 142hp | 105.9kw |
| Rated Net Power | 141hp | 105.2kw |
| Sae J1349 | 141hp | 105.2kw |
| Iso 9249 (1997) | 142hp | 105.9kw |
02 Operational Specification
| Operating Weight | 28360lb | 12863.9kg |
|---|
03 Transmission Specification
| Forward - 1 | 8mph | 12.9km/h |
|---|---|---|
| Reverse - 1 | 8mph | 12.9km/h |
04 Steering Specification
| Steering Angle - Each Direction | 40degrees | |
|---|---|---|
| Steering Cylinder, Two, Bore | 2.8in | 71.2mm |
| Maximum Working Pressure | 3500 psi | |
| Steering Articulation | 40degrees |
05 Transmission Specification
| 2 | 8mph | 12.9km/h |
|---|---|---|
| 3 | 17mph | 27.4km/h |
| 4 | 25mph | 40.3km/h |
| Standard Transmission Maximum Travel Speeds | 25mph | 40.3km/h |
06 Tires Specification
| Size | 20.5 R25 Radial (L-3) |
|---|
07 Buckets Specification
| Bucket Capacities | 1.9 m3 - 5.0 m3 2.5 yd3 - 6.5 yd3 |
|---|
08 Operating Specifications Specification
| Static Tipping Load - Full Turn | 16352lb | 7417.2kg |
|---|---|---|
| Articulation Angle | 40degrees | |
| Reach - Full Lift And 45 Degrees Dump | 3.3ft in | 1m |
| Dump Clearance At Full Lift And 45 Degrees Dump Angle | 9.4ft in | 2.9m |
09 Service Refill Capacities Specification
| Cooling System | 7.9gal | 30L |
|---|---|---|
| Fuel Tank | 51.5gal | 195L |
| Crankcase | 5.3gal | 20.1L |
| Hydraulic Tank | 23.8gal | 90.1L |
| Hydraulic System - Including Tank | 42.3gal | 160.2L |
| Transmission | 2.2gal | 8.4L |
| Front | 5.5gal | 20.9L |
| Rear | 5.5gal | 20.9L |
10 Cab Specification
| Rops | SAE J1040 MAY94, ISO 3471-1994 | |
|---|---|---|
| Fops | SAE J/ISO 3449 APR98 Level II, ISO 3449 1992 Level II |
11 Loader Hydraulic System Specification
| Pump Flow - Implement Pump | 40 gal/min | |
|---|---|---|
| Maximum Working Pressure | 3771 psi | |
| Raise | 5.5 s | |
| Dump | 1.5 s | |
| Lower, Empty, Float Down | 2.6 s | |
| Total | 9.6 s | |
| Bore (1) | 4.3in | 109.3mm |
| Stroke (1) | 28.7in | 729mm |
| Bore (2) | 5.1in | 129.6mm |
| Stroke (2) | 21.9in | 556.3mm |
| Hydraulic Cycle Time | 9.6 s |
12 Dimensions Dimensions
| Ground Clearance | 1.25ft in | 381mm |
|---|---|---|
| Carry Height | 1.5ft in | 0.46m |
| Centerline Of Front Axle To Hitch | 4.91ft in | 1.5m |
| Digging Depth | 3.8in | 96.52mm |
| Dump Angle At Maximum Lift | 50degrees | |
| Dump Clearance At Maximum Lift - 45 Degrees | 9.4ft in | 2.87m |
| Height - Center Of Axle | 2.21ft in | 0.68m |
| Height - Top Of Rops/Fops | 10.9ft in | 3.33m |
| Length - Rear Axle To Bumper | 6.5ft in | 1.99m |
| Overall Height - Bucket Raised | 16.61ft in | 5.06m |
| Overall Length | 24.4ft in | 7437.12mm |
| Rack Back Angle - Carry | 45degrees | |
| Rack Back Angle - Maximum Lift | 54degrees | |
| Reach At Maximum Lift And 45 Degrees Dump | 3.3ft in | 1.01m |
| Wheel Base Length | 9.81ft in | 2.99m |
| Bucket Pin Height - Maximum Lift | 12.75ft in | 3.89m |
| Width - Over Tires | 8.33ft in | 2.54m |
?Questions & answersfrom this machine's data
- How much does a Caterpillar 924K wheel loader weigh?
- A Caterpillar 924K wheel loader has an operating weight of 28,360 lb (12,863.9 kg).
- What is the ground clearance of a Caterpillar 924K wheel loader?
- A Caterpillar 924K wheel loader has a ground clearance of 1.3 ft (381 mm).
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.