Specification sheet Wheel Loader Ref caterpillar-924hz-wheel-loader
Caterpillar 924Hz
The Caterpillar 924Hz is a wheel loader with an operating weight of 24,180 lb (10,967.87 kg), and a dig depth of 0.14 ft (41.91 mm).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
24,180lb
10,967.87kg
Dig depth
0.14ft
41.91mm
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Caterpillar 924Hz sits at the compact end of its class:
- Operating weight 24,180 lb lighter than 88% (n=439)
Not positioned on engine power, bucket capacity — withheld or unpublished for this machine.
01 Engine Specification
| Displacement | 403cu in | 6.7L |
|---|---|---|
| Net Torque | 482lb ft | 653.6Nm |
| Peak Torque | 496lb ft | 672.5Nm |
| Bore | 4.2in | 105mm |
| Stroke | 5in | 127mm |
| Rated Net Power | 128hp | 95.5kw |
| Sae J1349 (2) | 138hp | 103kw |
| Iso 9249 (1997) (2) | 139hp | 103.7kw |
| Eec 80/1269 (2) | 139hp | 103.7kw |
| Sae J1349 (1) | 128hp | 95.5kw |
| Iso 9249 (1997) (1) | 130hp | 97kw |
| Eec 80/1269 (1) | 130hp | 97kw |
| Maximum Net Power - 1800 Rpm | 138hp | 103kw |
02 Operational Specification
| Operating Weight | 24180lb | 10967.9kg |
|---|
03 Steering Specification
| Steering Angle - Each Direction | 40degrees | |
|---|---|---|
| Minimum Turning Radius - Over Tires | 200in | 5080mm |
| Steering Cylinder, Two, Bore | 2.8in | 69.9mm |
| Hydraulic Output At 2300 Engine Rpm And 6900 Kpa (1000 Psi) | 27 gal/min | |
| Maximum Working Pressure | 3000 psi |
04 Transmission Specification
| Forward - 1 (1) | 4.2mph | 6.8km/h |
|---|---|---|
| Reverse - 1 (1) | 4.2mph | 6.8km/h |
| Forward - 1 (2) | 2.3mph | 3.8km/h |
| 2 (2) | 4.7mph | 7.6km/h |
| 3 (2) | 12.2mph | 19.7km/h |
| 4 (2) | 24.2mph | 39km/h |
| Reverse - 1 (2) | 2.5mph | 4.1km/h |
| 2 (3) | 5mph | 8.1km/h |
| 3 (3) | 13.2mph | 21.3km/h |
| 2 (1) | 7.6mph | 12.3km/h |
| 3 (1) | 13.5mph | 21.8km/h |
| 4 (1) | 23.9mph | 38.5km/h |
05 Steering Specification
| Steering Articulation | 40degrees |
|---|
06 Transmission Specification
| Standard Transmission Maximum Travel Speeds | 23.9mph | 38.5km/h |
|---|---|---|
| Optional Low Speed Transmission Maximum Travel Speeds | 24.2mph | 39km/h |
07 Tires Specification
| Tread Width | 6.2ft in | 1.9m |
|---|---|---|
| Size | 20.5 R25 Radial (L-3) |
08 Buckets Specification
| Bucket Capacities | 1.7 m3 - 2.1 m3 2.2 yd3 - 2.7 yd3 |
|---|
09 Operating Specifications Specification
| Static Tipping Load - Full Turn | 16844lb | 7640.4kg |
|---|---|---|
| Articulation Angle | 40degrees | |
| Reach - Full Lift And 45 Degrees Dump | 2.6ft in | 0.8m |
| Dump Clearance At Full Lift And 45 Degrees Dump Angle | 9.3ft in | 2.9m |
10 Service Refill Capacities Specification
| Cooling System | 8.5gal | 32.2L |
|---|---|---|
| Fuel Tank | 59.4gal | 224.9L |
| Crankcase | 4.4gal | 16.7L |
| Hydraulic Tank | 18.5gal | 70.1L |
| Hydraulic System - Including Tank | 33gal | 125L |
| Transmission | 6.1gal | 23.1L |
| Front | 5.5gal | 20.9L |
| Rear | 5.5gal | 20.9L |
11 Cab Specification
| Rops | SAE J1040 MAY94, ISO 3471-1994 | |
|---|---|---|
| Fops | SAE J231 JAN81, ISO 3449-1992 Level II |
12 Loader Hydraulic System Specification
| Pump Flow - Implement Pump | 40.15 gal/min | |
|---|---|---|
| Output At 2,300 Engine Rpm And 6900 Kpa (1000 Psi) With Sae 10w Oil At 65 Degreesc (150 Degreesf) | 39.5 gal/min | |
| Maximum Working Pressure | 3755 psi | |
| Raise | 5.2 s | |
| Dump | 1.1 s | |
| Lower, Empty, Float Down | 2.7 s | |
| Total | 9 s | |
| Bore (1) | 4.3in | 108mm |
| Stroke (1) | 29.7in | 754.4mm |
| Bore (2) | 4.8in | 120.7mm |
| Stroke (2) | 20.5in | 520.7mm |
| Hydraulic Cycle Time | 9 Seconds | |
| Relief Pressure - Implement Pump | 3755 psi |
13 Dimensions Dimensions
| Ground Clearance | 1.43ft in | 435.87mm |
|---|---|---|
| Bucket Pin Height - Maximum Lift | 12.33ft in | 3.76m |
| Carry Height | 1.43ft in | 0.44m |
| Centerline Of Front Axle To Hitch | 4.59ft in | 1.4m |
| Digging Depth | 1.65in | 41.91mm |
| Dump Clearance At Maximum Lift - 45 Degrees | 9.28ft in | 2.83m |
| Height - Center Of Axle | 2.27ft in | 0.7m |
| Height - Top Of Exhaust Stack | 10.53ft in | 3.21m |
| Height - Top Of Hood | 87.36in | 2218.95mm |
| Height - Top Of Rops/Fops | 10.59ft in | 3.23m |
| Length - Rear Axle To Bumper | 6.44ft in | 1.97m |
| Overall Height - Bucket Raised | 15.78ft in | 4.81m |
| Overall Length | 22.63ft in | 6897.63mm |
| Reach At Maximum Lift And 45 Degrees Dump | 2.6ft in | 0.8m |
| Bucket Clearance-Maximum Lift/Carry | 11.26ft in | 3.44m |
| Wheel Base | 9.19ft in | 2.81m |
?Questions & answersfrom this machine's data
- How much does a Caterpillar 924Hz wheel loader weigh?
- A Caterpillar 924Hz wheel loader has an operating weight of 24,180 lb (10,967.9 kg).
- What is the ground clearance of a Caterpillar 924Hz wheel loader?
- A Caterpillar 924Hz wheel loader has a ground clearance of 1.4 ft (435.9 mm).
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.